Application Advice; Maintenance & Service - Skil 4900 Original Instructions Manual

! ensure that the front end of the blade extends
through footplate E for the entire stroke length
• Removing saw blade 8
- press blade clamp D forward and hold it in that
position
- pull out blade
- release blade clamp D
• Adjustable footplate 9
- footplate E tilts in order to keep as much of its
surface in contact with the workpiece
- adjust footplate by holding the saw fi rmly and turning
footplate to desired position
• Blade storage compartment 0
- ensure that storage compartment F is closed to
prevent blades from falling out
• Operating the tool
! securely clamp the workpiece
- mark the cutting line on the workpiece
- select desired sawing speed with wheel C 2
- connect plug to power source (light B turns on
indicating that the tool is receiving power) !
- hold the tool with one hand on handle G 2 and the
other on the insulated barrel grip H 2
- switch on the tool
! the tool should run at full speed before the blade
enters the workpiece
- guide the tool along the marked cutting line
- keep footplate E 2 fi rmly against the workpiece to
minimize counter-force and vibration
• Holding and guiding the tool
! while working, always hold the tool at the grey-
coloured grip area(s) @
- keep ventilation slots J 2 uncovered
- do not apply too much pressure on the tool; let the
tool do the work for you
! ensure that the saw blade extends beyond the
work throughout the stroke #
• Adjusting effective stroke length $
- use both adjustment screws K for sliding footplate E
forward/backwards in order to enlarge/reduce the
effective stroke length
! do not attempt to adjust the effective stroke
length with screw L which is pre-set at
manufacturing
• Plunge cutting %a
Plunge cuts can be made in wood and other soft
materials without pre-drilling a hole
- select position 1, 2 or 3 with wheel C
- mark desired cutting line on the workpiece
- position the tool with one edge of footplate E fi rmly
against the workpiece
- place the tip of the blade (not running) on the cutting
line
- tilt the tool so that the blade does not touch the
workpiece
- switch on the tool and carefully engage the moving
saw blade into the workpiece
- after the blade has penetrated through the workpiece
continue sawing along the marked cutting line
! do not make plunge cuts in metal materials
SKIL_IB4900_BR.indd 9 SKIL_IB4900_BR.indd 9
• For easier plunge cutting, use a thick saw blade, or
mount the blade with the teeth facing upward and hold
the saw upside down as illustrated %b

APPLICATION ADVICE

• Use the appropriate saw blades ^
• When cutting metals, lubricate saw blade regularly with
oil
• Splinter-free cutting
- cover cutting-line with several layers of wide tape
before cutting
- always face the good side of the workpiece down
• For more tips see www.skil.com.br
• Vibration level
The vibration emission level stated at the back of this
instruction manual (indicated by an asterisk) has been
measured in accordance with a standardised test given
in EN 60745; it may be used to compare one tool with
another and as a preliminary assessment of exposure to
vibration when using the tool for the applications
mentioned
- using the tool for different applications, or with
different or poorly maintainted accessories, may
signifi cantly increase the exposure level
- the times when the tool is switched off or when it is
running but not actually doing the job, may
signifi cantly reduce the exposure level
! protect yourself against the effects of vibration by
maintaining the tool and its accessories, keeping
your hands warm, and organizing your work
patterns
MAINTENANCE / SERVICE
• Always keep tool and cord clean (especially the
ventilation slots J 2)
! disconnect the plug before cleaning
• If the tool should fail despite the care taken in
manufacturing and testing procedures, repair should be
carried out by an after-sales service centre for SKIL
power tools
- send the tool undismantled together with proof of
purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of
the tool are listed on www.skil.com.br)
ENVIRONMENT
• Do not dispose of electric tools, accessories and
packaging together with household waste material
(only for EU countries)
- in observance of European Directive 2002/96/EC on
waste of electric and electronic equipment and its
implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol & will remind you of this when the need for
disposing occurs
9
13-05-2009 17:04:37 13-05-2009 17:04:37