i. Tech Dynamic Bluetooth Headset i.Cube User Manual page 2

Getting Started
Before using your i.Cube ("headset") for the first time, please ensure that
1. the headset is fully charged;
2. the fully charged headset must be paired and connected with a Bluetooth mobile
phone.
Charging Your Headset
The headset comes with a built-in rechargeable battery. Prior to using the headset for
the first time, you are recommended to fully charge the battery.
Charging Socket
Use only the supplied charger to charge the headset.
Pairing Your Headset with Two Mobile Phones (Multipoint)
i.Cube supports a Multipoint function to allow simultaneous pairing of the headset
with two mobile phones.
1. Follow the pairing procedure as instructed in "Pairing Your Headset with a
Bluetooth Mobile Phone" to pair the headset with the first mobile phone.
2. Repeat the pairing procedure for the second mobile phone.
3. On the first mobile phone's menu, activate its Bluetooth connection with the
headset.
Using Your Headset
Function Button
Power ON Press and hold the MFB for 2
seconds
When you turn on your headset for the first time, the headset automatically enters
the pairing mode, i.e. the status indicator flashes alternating blue and red lights.
This allows you to immediately pair your headset and mobile phone.
If your headset is paired with your mobile phone, press the MFB once more after
you turned on the headset to re-connect the mobile phone and the headset.
Power OFF Press and hold the MFB for 2
seconds
If you do not plan to use the headset for a while, you are recommended to turn off
the Bluetooth function of your mobile phone.
fig.2
5
Audio Status Indicator
a short beep Flashing blue light
a long beep Red light for two seconds
and then the light goes off
7
Charging Your Headset (cont'd)
Status Status Indicator
• Charging • Red light
• Fully charged • Blue light
• Low battery • Flashing red light
• Out of battery • The light goes off
♦ 3 hours are required to fully charge the headset.
♦ Charging indication will be delayed for a few seconds if the headset has not been used
for a long time or the battery is drained.
Pairing Your Headset with a Bluetooth Mobile Phone
1) Ensure the headset is off.
2) To activate the pairing mode, press and hold the headset's MFB for 8 seconds without
releasing your finger until its status indicator flashes alternating blue and red lights.
3) Activate your mobile phone's Bluetooth, search Bluetooth devices, select "i.Cube" and
enter the passcode "0000". When the pairing is completed, the headset's status indicator
will flash a blue light rapidly five times.
If the pairing cannot be completed within three minutes after the pairing mode has been
activated, the headset's status indicator will flash purple rapidly five times and then turns
off. Repeat steps 1 to 3 to pair both devices again.
Using Your Headset (cont'd)
Function Button
Answer a Call Press the MFB once
Answer a Second Call Press the MFB once to terminate a beep
intended for your other the first call, then press the MFB
mobile phone once again to answer the second
call
End a Call Press the MFB once
Adjust Volume Press the Vol＋/－once to
increase / decrease by 1 level
Mute a Call Press either volume key for 2
seconds
Cancel Call Muting Press either volume key for 2
seconds
Voice Dialing Press the MFB once
Say the voice tag as soon as you hear the short beep and you must have recorded the voice
tag into your mobile phone.
Last No. Redial Double click the MFB
Audio
• a short beep every 1 minute
6
Audio Status Indicator
Flashing blue light
Flashing purple light
when there is a second
call intended for your
other mobile phone
Flashing blue light
a short beep Flashing blue light
2 beeps every Flashing blue light
5 seconds
2 short beeps Flashing blue light
a short beep Flashing blue light
Flashing blue light
8