Table of Contents
Advertisement
Quick Links
2005 Hutchison Harbour Ring Enterprises Limited
All rights in this publication are reserved and no part may
be reproduced without the prior written permission of
the publisher. The contents of this publication are
believed to be correct at the time of going to press, but
any information, specifications, products or services
mentioned may be modified, supplemented or
withdrawn without further notice.
The Stylized i.Tech logos are trademarks owned by
Hutchison Harbour Ring Enterprises Limited or its
affiliates.
®
Bluetooth
and the Bluetooth logos are trademarks
owned by Bluetooth SIG, Inc, USA and licensed to i.Tech
Dynamic Limited.
01/2006
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired
operation.
Caution: Changes or modifications not expressly
approved by the party responsible for compliance could
void the user's authority to operate the equipment.
i.Tech declares under our sole responsibility that the
headset is in conformity with the provisions of the
following Council Directives: 1999/5/EC
S3J-51A05053-01A
i.Tech Arrow II
User Guide
Advertisement
Table of Contents
Related Manuals for i. Tech Dynamic II
Summary of Contents for i. Tech Dynamic II
-
Page 1: User Guide
Council Directives: 1999/5/EC ® Bluetooth and the Bluetooth logos are trademarks owned by Bluetooth SIG, Inc, USA and licensed to i.Tech Dynamic Limited. 01/2006 i.Tech Arrow II User Guide S3J-51A05053-01A... - Page 2 Arrow II headset offers you the freedom to make and receive calls while on the move or at the office. The i.Tech Arrow II headset is compatible with mobile handsets that support the Bluetooth Headset and Handsfree Profiles to...
-
Page 3: Table Of Contents
Is in conformity with the following essential requirements of Council Directive 1999/5/EC ( referred to as R&TTE Directive ) : Article 3.1a, 3.1.b and 3.2. and the product is manufactured in accordance with Annex II of above directive. A copy of the Declaration of Conformity can be found at: http://www.itechdynamic.com... -
Page 4: I.tech Arrow Ii Overview
7. Microphone 4. Ear Hook 8. Volume Keys (fig. 1) Getting Started To use your i.Tech Arrow II (“the headset”), please follow these simple steps: Charge your headset Pair your headset with a Bluetooth-enabled mobile handset Product Specifications Bluetooth Specification:... -
Page 5: Troubleshooting
If the above steps do not solve your problem, please recharge the headset and remove your mobile handset’s battery for a while. The i.Tech Arrow II Headset is compliant with and adopts the Bluetooth Specification 1.2. However, interoperability between the device and other Bluetooth-enabled products is not guaranteed because it depends on compatibility. -
Page 6: Normal Charging Time
Charging Your Headset Connect the charger to an AC wall outlet and the charger plug to the headset’s charging socket (fig.2). The LED will be red while charging. IMPORTANT Charging indication will be delayed for a few seconds if the headset has not been used for a long time or the battery is drained. -
Page 7: Turning Your Headset On And Off
Built-in Battery Do not attempt to replace the headset’s battery yourself as it is • built-in and is not changeable Charge the battery in accordance with the instructions supplied • with this user guide. Only use the manufacturer supplied charger when charging the •... -
Page 8: Pairing Your Headset
Pairing Your Headset Up to 1 metre Prior to using your headset for the first time, you must pair it with a Bluetooth-enabled mobile handset. The information on the next page describes pairing instruction for a typical Bluetooth-enabled mobile handset. Headset pairing procedure is subject to different models of mobile handsets. -
Page 9: Adjusting The Volume
5. Set the mobile handset to search for Bluetooth devices within 1 metre as instructed in the mobile handset user guide and select “i.Tech Arrow II” from the list. 6. Enter the pre-programmed passkey “0000” and press “OK” to pair your headset and mobile handset. -
Page 10: Using Your Headset
Using Your Headset Answering a Call When there is an incoming call, you will hear ringing through the speaker. Press the MFB to accept the call or answer the call via your mobile handset in the normal way. Ending a Call Press the MFB to end your call or end the call via your mobile handset in the normal way.
Need help?
Do you have a question about the II and is the answer not in the manual?
Questions and answers