Table of Contents
Advertisement
OPERATION MANUAL
OPERATION & MAINTENANCE
MANUAL
IMPORTANT: READ BEFORE OPERATING
HIGH PRESSURE WASHERS
NATURAL GAS & PROPANE
HN SERIES
NATURAL GAS HEAT LINK SERIES
HYDRO TEK SYSTEMS, INC.
10418 Enterprise Drive
Redlands, CA USA 92374
PH(909)799-9222 FAX(909)799-9888
Website: www.hydroteksystems.com
© 2003 Hydro Tek Systems, Inc. 8/2004
$15.00
Advertisement
Table of Contents
Related Manuals for Hydro Tek HN SERIES
Summary of Contents for Hydro Tek HN SERIES
- Page 1 IMPORTANT: READ BEFORE OPERATING HIGH PRESSURE WASHERS NATURAL GAS & PROPANE HN SERIES NATURAL GAS HEAT LINK SERIES HYDRO TEK SYSTEMS, INC. 10418 Enterprise Drive Redlands, CA USA 92374 PH(909)799-9222 FAX(909)799-9888 Website: www.hydroteksystems.com © 2003 Hydro Tek Systems, Inc. 8/2004...
-
Page 2: Table Of Contents
TABLE OF CONTENTS INTRODUCTION ..........................4 Statement of Warranty SAFETY WARNINGS ......................... 5-6 Electrical Precautions Fire Precautions Ventilation Precautions Spray Injection Precautions Personal Hazard Precautions OPERATING INSTRUCTIONS ......................6-7 Before Start Up Operation Shut Down & Antifreeze Protection SYSTEM INFORMATION ......................... 8-11 Power System ........................... -
Page 3: Introduction
8. Repairs made necessary by the use of parts which are either not obtained from or approved by Hydro Tek. 9. Actions or inactions by any Hydro Tek distributor giving rise to or causing a warranty exclusion or promise of additional warranty. -
Page 4: Safety Warnings
This supersedes any and all previous warranty statements for exhaust stack to prevent burns. products purchased after June 1, 2001. Hydro Tek is not liable for 4. DO NOT store fuel or other flammable materials near the burner or any indirect, incidental or consequential damages including but not limited other open flame. -
Page 5: Safety Warnings
4. STEAM: Insert steam nozzle and turn thermostat to 250º HN SERIES steam setting. The steam nozzle is sized for approximately 1. CHECK OIL AND FLUID LEVELS: Check pump oil by 25% less water volume than the hot water mode. -
Page 6: Operating Instructions
OPERATING INSTRUCTIONS HN SERIES OPERATING WASHING OPERATION & CONDITIONS TECHNIQUES When washing always start from the bottom up, and do Heat rise will vary depending on inlet water temperature and the final rinse from the top down. This will keep the water from environmental conditions. -
Page 7: System Information
(opposite the head) of the pump and reset itself after the motor has cooled. should be filled to the middle with Pump Oil , available at your Hydro Tek dealer. If the oil becomes milky in HORSE 115V... -
Page 8: Heating System
The float tank and filter (located component ruptures, you should take the ma- inside the tank) should be flushed out if chine in to an authorized Hydro Tek dealer. Do debris accumulates in the bottom. If the float not plug off and continue to run. -
Page 9: Pressure Delivery System
If the hose is not replaced when worn or if it is not burner does not light within 90 seconds turn the burner replaced by a Hydro Tek original equipment hose, it may switch off and on again to start the ignition sequence over. -
Page 10: System Information
SYSTEM INFORMATION NOZZLES: The spray nozzle is a precisely machined orifice made of hardened stainless steel. The orifice size is matched to the output of your machine to attain the proper flow and pressure that your machine was designed for. The orifice or hole of the nozzle will begin to get larger as the nozzle becomes worn. -
Page 11: Gun/Wand Assembly - Trigger Gun, Wand, & Quick Coupler Nozzles - Spray Nozzles And Steam Nozzle Accessories - Wet Sandblaster, Turbo Nozzle, Hoses And Reels, Wands, Injectors
ACCESSORIES ACCESSORIES: WARNING: If your unit is equipped with 250º steam option, only use 250º rated hose. WET SANDBLASTER Low pressure inlet garden hose is available in 50 and 100 The wet sandblaster is a system that intro- foot lengths. Premium quality, 200 PSI rated hose is duces sand into the water stream for abrasive recommended to be used and is available at your local blasting. -
Page 12: Trouble Shooting Guide
TROUBLE SHOOTING GUIDE PROBLEM PROBABLE CAUSE* REMEDY Power System: Electric Motor Driven Electric motor does not start. Check cord, plug, socket, and breaker. Check No electric power. Voltage Thermal overload in the motor/or starter has been tripped. Reset manual overload by depressing the thermal switch on the outside of the motor or starter after the motor has cooled. - Page 13 TROUBLE SHOOTING GUIDE PROBLEM PROBABLE CAUSE* REMEDY Heating/Burner System-Natural Gas or LP Fired WARNING Disconnect MV Wire At Gas Valve Before Trouble Shooting. Pilot will not light, burner will not fire. Burner switch not on. Turn switch on / press reset switch. Pull trigger.
-
Page 14: Service Record
SERVICE RECORD SERVICE RECORD MODEL# _____________________ SERIAL# ____________________ Date of Service Number of Run Hrs. Service Performed Mo./Day/Year Since Last Service... -
Page 15: Service/Maintenance Information
Attention to regular preventative maintenance procedures will assist in preserving the performance of your equipment. Contact your Hydro Tek dealer for maintenance. A small investment in MAINTENANCE SCHEDULE Pump Oil Inspect...
Need help?
Do you have a question about the HN SERIES and is the answer not in the manual?
Questions and answers