Carrier AQUAZONE 50HQL072-120 Installation, Start-Up And Service Instructions Manual page 26

RATED
CFM
0.0
BHP 1.10
3400
RPM 1014
Turns Open 3.0
BHP 1.26
3600
RPM 1052
Turns Open 2.5
BHP 1.44
3800
RPM 1090
Turns Open 1.5
BHP 1.63
4000
RPM 1127
Turns Open 0.5
BHP 1.84
4200
RPM 1164
Turns Open 4.0
BHP 2.07
4400
RPM 1202
Turns Open 3.5
BHP 2.30
4600
RPM 1237
Turns Open 3.0
LEGEND
— — Operation Not Recommended
ARI — Air Conditioning and Refrigeration Institute
BHP — Brake Horsepower
ESP — External Static Pressure
ISO — International Organization for Standardization
RPM — Revolutions Per Minute
A — Units with Standard Static Sheave/Standard Motor Option
B — Units with Low-Static Sheave/Standard Motor Option
C — Units with High-Static Sheave/Standard Motor Option
D — Units with Standard Static Sheave/Large 3 Hp Motor Option
E — Units with High-Static Sheave/Large 3 Hp Motor Option
NOTES:
1. Boldface requires 3 hp motor.
RATED
CFM
0.0
BHP 0.36
2000
RPM 600
Turns Open 3
BHP 0.45
2200
RPM 633
Turns Open 2
BHP 0.55
2400
RPM 670
Turns Open 1.5
BHP 0.68
2600
RPM 708
Turns Open 0.5
BHP 0.82
2800
RPM 744
Turns Open 4.5
BHP 0.97
3000
RPM 777
Turns Open 4
BHP 1.14
3200
RPM 807
Turns Open 3.5
LEGEND
A — Standard Static Sheave/Standard Motor
B — Low-Static Sheave/Standard Motor
C — High-Static Sheave/Standard Motor Option
E — High-Static Sheave/Large Motor
ARI — Air Conditioning and Refrigeration Institute
BHP — Brake Horsepower
ESP — External Static Pressure
ISO — International Organization for Standardization
RPM — Revolutions Per Minute
NOTES:
1. Bold numbers require 2 horsepower motor.
2. Due to alternate sheaves, 'Turns Open' may vary within ±0.5 turn from
the position shown above.
Table 8 — 50HQL120 Blower Performance Data
0.1 0.2 0.3 0.4
1.15 1.20 1.25 1.30
1043 1072 1102 1129
B
2.5 2.0 1.0 0.5
1.31 1.37 1.42 1.48
1081 1109 1136 1163
1.5 1.0 0.5 4.0
1.50 1.56 1.61 1.67
1118 1145 1172 1199
1.0 0.0 4.0 3.5
1.70 1.76 1.82 1.88
1154 1181 1207 1232
4.5 4.0 3.5 3.0
1.91 1.98 2.04 2.10
1191 1217 1241 1266
3.5 3.0 2.5 2.5
2.13 2.20 2.27 2.33
1227 1251 1276 1300
3.0 2.5 2.0 1.5
2.37 2.44 2.51 2.59
1262 1287 1310 1333
2.5 2.0 1.5 1.0
Table 9 — 50VQL080 Blower Performance Data
0.1 0.2 0.3 0.4
0.39 0.43 0.47 0.51
B
641 681 720 757
2 1 0.5 4.5
0.49 0.53 0.57 0.61
671 708 745 780
1.5 0.5 4.5 4
0.60 0.64 0.69 0.73
705 740 774 807
1 4.5 4 3.5
0.73 0.77 0.82 0.87
741 773 805 837
4.5 4 3.5 2.5
0.87 0.92 0.97 1.02
775 806 836 866
4 3.5 3 2
1.03 1.08 1.14 1.19
807 836 865 893
3.5 3 2 1.5
1.19 1.25 1.31 1.36
835 862 890 917
3 2.5 1.5 1
EXTERNAL STATIC PRESSURE (in. wg)
0.5 0.6 0.7 0.8
1.35 1.40 1.45 1.50
1156 1183 1209 1234
4.5 4.0 3.5 3.0
1.53 1.58 1.63 1.68
1190 1216 1241 1266
A
3.5 3.0 2.5 2.5
1.73 1.78 1.84 1.89
1223 1248 1273 1298
3.0 2.5 2.0 1.5
1.94 2.00 2.06 2.11
1257 1281 1306 1329
2.5 2.0 1.5 1.0
2.16 2.22 2.28 2.34
1291 1314 1337 1360
D
2.0 1.5 1.0 0.5
2.40 2.46 2.53 2.60
1323 1346 1369 1392
1.0 1.0 0.5 0.0
2.66 2.73 2.80 2.87
1356 1379 1402 1423
0.5 0.0 4.0 3.5
2. Units factory shipped at ISO/ARI setting with standard static
sheave and drive at 2.5 turns open (4000 cfm at 0.5 in. wg ESP).
Other speeds require field selection.
3. For applications requiring higher static pressures, contact your local
representative.
4. Based on 2-11x10 blowers.
5. Performance data does not include drive losses and is based on
sea level conditions.
6. All airflow is rated at lowest voltage if unit is dual voltage rated, i.e.,
208V for 208-230V units.
7. For wet coil performance first calculate the face velocity of the air
coil (Face Velocity [fpm] = Airflow [cfm] / Face Area [sq ft]). Then for
velocities of 200 fpm reduce the static capability by 0.03 in. wg,
300 fpm by 0.08 in. wg, 400 fpm by 0.12 in. wg and 500 fpm by
0.16 in. wg.
EXTERNAL STATIC PRESSURE (in. wg)
0.5 0.6 0.7 0.8 0.9
0.55 0.59 0.63 0.67 0.71
794 829 864 898 931
3.5 3 2 1.5
0.65 0.70 0.74 0.79 0.83
814 848 881 913 945
3 2.5 2 1.5 0.5
0.78 0.82 0.87 0.92 0.97
A
840 872 903 934 964
2.5 2 1.5 1 0.5
0.92 0.97 1.02 1.07 1.12
867 898 927 957 985
2 1.5 1 0.5
1.08 1.13 1.18 1.24 1.29
895 924 952 980 1007
1.5 1 0.5 0
1.25 1.30 1.36 1.41 1.47
921 948 975 1002 1028
1 0.5 0 3 2.5
1.42 1.48 1.54 1.60 1.66
943 969 995 1021 1046
0.5 3 3 2.5
3. Units factory shipped with standard static sheave and drive at 2.5
turns open (2600 cfm at 0.4 in. wg ESP Wet Coil). Other speeds
require field selection.
4. ISO/ARI rating point with standard static sheave and drive at 2 turns
open (2600 cfm at 0.48 in. wg ESP Wet Coil). Other speeds require
field selection.
5. For applications requiring higher static pressures, contact your local
representative.
6. Performance data does not include drive losses and is based on sea
level conditions.
7. Do not operate in gray region.
8. All airflow is rated at lowest voltage if unit is dual voltage rated, i.e.,
208 v for 208-230-v units.
9. For wet coil performance first calculate the face velocity of the air coil
(Face Velocity [fpm] = Airflow [cfm]/Face Area [sq ft]). Then for veloci-
ties of 200 fpm reduce the static capability by 0.03 in. wg, 300 fpm by
0.08 in. wg, 400 fpm by 0.12 in. wg and 500 fpm by 0.16 in. wg.
26
0.9 1.0 1.1 1.2
1.54 1.59 1.63 1.68
1260 1285 1309 1333
2.5 2.0 1.5 1.0
1.74 1.79 1.84 1.89
1291 1315 1338 1362
2.0 1.5 1.0 4.5
1.95 2.00 2.06 2.11
1321 1345 1368 1391
1.0 1.0 0.5 0.0
2.17 2.22 2.28 2.34
1352 1375 1398 1420
0.5 0.0 0.0 3.5
2.40 2.47 2.53 2.59
1383 1406 1427 1449
0.0 3.5 3.5 3.0
2.66 2.73 2.79 2.86
1414 1435 1457 1478
3.5 3.5 3.0 2.5
2.95 — — —
1444 — — —
3.0 — — —
1.0 1.1 1.2
0.76 0.80 0.84
964 996 1027 1058
1 0.5 3 2.5
0.88 0.92 0.97
976 1006 1036 1066
C
0 3 2.5
1.02 1.07 1.11
993 1022 1051 1079
3 2.5 2
1.17 1.22 1.28
1013 1041 1069 1096
0 3 2.5 2
1.34 1.40 1.45
1034 1061 1087 E 1113
3 2.5 2 1.5
1.53 1.59 1.65
1054 1079 1104 1129
2 2 1.5
1.72 1.78
1071 1095
2 2 1.5
1.3 1.4 1.5
1.73 1.77 1.82
1356 1380 1403
C
4.5 4.0 4.0
1.94 1.99 2.04
1385 1408 1430
4.0 3.5 3.5
2.16 2.21 2.26
1413 1435 1457
3.5 3.5 3.0
2.39 2.45 2.50
1441 1463 1485
E
3.0 3.0 2.5
2.65 2.71 2.77
1470 1492 1513
2.5 2.5 2.0
2.93 2.99 —
1500 1520 —
2.5 2.0 —
— — —
— — —
— — —
1.3 1.4 1.5
0.89 0.93 0.98
1088 1117
2 1.5 1
1.02 1.06 1.11
1095 1123
2 1.5 1
1.16 1.22 1.27
1107 1134
2 1.5 1
1.33 1.38 1.44
1122 1149
1.5 1 0.5
1.51 1.57 1.62
1138 1164
1.5 1 0.5
1.70 1.76 1.82
1154 1178
1 0.5 0