Download Print this page

Miele CS 1028 Operating And Installation Instructions

Miele cs 1028 gas combiset operating and installation instructions.
Hide thumbs

Advertisement

Operating and Installation
Instructions
Gas Combiset
CS 1028
®
®
en - US, CA
To prevent accidents and
machine damage,
read the Operating Manual
before
installation or use.
M.-Nr. 07 369 720

Advertisement

   Summary of Contents for Miele CS 1028

  • Page 1: Operating And Installation Instructions

    Operating and Installation Instructions Gas Combiset CS 1028 ® ® en - US, CA To prevent accidents and machine damage, read the Operating Manual before installation or use. M.-Nr. 07 369 720...

  • Page 2

    WARNING: If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury or death. – Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

  • Page 3: Table Of Contents

    Contents IMPORTANT SAFETY INSTRUCTIONS....... . . 4 Guide to the combiset ..........9 Burner .

  • Page 4: Important Safety Instructions

    IMPORTANT SAFETY INSTRUCTIONS Children WARNING- When using your gas Children should not be left appliance follow basic unattended in an area where the precautions, including the appliance is in use. Never allow following: children to sit or stand on any part of the appliance.

  • Page 5

    Install the appliance so that the power cord and gas piping do not Installation, repair and maintenance come into contact with any portion of work should be performed by a Miele the combiset which may become hot authorized service technician. Work by during use.

  • Page 6

    Do not let the potholder applications. Please contact the touch the hot heating elements. Do not nearest Miele Dealer or the Miele use towels or other bulky items near the Technical Service Department with appliance.

  • Page 7

    IMPORTANT SAFETY INSTRUCTIONS Do not use pans that extend past Always position pan handles and the burner grate. Using larger pans utensils inward so they do not extend may cause the flames to spread out over adjacent work areas, burner or the and damage the surrounding edge of the combiset.

  • Page 8

    In the event of damage or defect, turn off the appliance immediately. Turn off the gas shut off valve and disconnect completely from the electrical supply. Contact the Miele Technical Service Department. Do not use the appliance until it has been repaired.

  • Page 9: Guide To The Combiset

    Guide to the combiset a Burner grate b Burner c Control knob...

  • Page 10: Burner

    Guide to the combiset Burner d Burner cap e Burner head f Cover plate g Ignitor h Ignition safety control (Thermocouple) i Burner base...

  • Page 11: Before Using The Combiset

    Before using the combiset Cleaning the combiset Metal components have a protective coating which may give off a slight odor Before using for the first time clean the the first time your new appliance is appliance as follows: heated. ^ Remove any protective foil. The harmless odor will dissipate after a ^ Wash the removable parts of the gas short time and does not indicate a...

  • Page 12: Operation

    Operation Turning on and off / Regulating Turning on The control knob is used to turn on the burner and to regulate the strength of the flame. ß The gas supply is turned off * Ignition setting & Highest flame ^ To turn on the burner, press the / Lowest flame control knob down and turn it...

  • Page 13: Using The Cooktop During A Power Failure

    Operation Using the cooktop during a Adjusting the flame power failure The burner can be variably adjusted between the lowest and highest flame If there is an interruption to the by turning the control knob. electrical supply, the gas can be ignited using a match.

  • Page 14: Pans

    Pans Pan size Suitable pans – Set the combiset to a high flame Unlike pans used on an electric when using a large diameter pan and combiset, the bases do not need to be low flame when using a small even for good results.

  • Page 15: Safety Features

    Safety features Ignition Safety Control This gas combiset incorporates an Ignition Safety Control which stops the supply of gas if the flame goes out. ^ To reignite the burner, turn the control knob clockwise to “ß”, then turn on the burner as usual. This safety feature is not operated by electricity, it will be active even if the appliance is in use during a power...

  • Page 16: Cleaning And Care

    Keep the ignitor in the burner dry. If These cleaning products are available it gets wet it will not spark. from Miele. Dry your combiset thoroughly after Do not use stainless steel cleaner on or cleaning it to prevent lime deposits.

  • Page 17: Burner

    Cleaning and care Burner Reassembling the burner Do not clean any parts of the burner in a dishwasher. The burner can be dismantled and cleaned when cool. ^ Remove the burner parts and wash them in a solution of warm water and liquid dish soap.

  • Page 18: Frequently Asked Questions

    Frequently asked questions Repairs should only be carries out by an authorized technician in accordance with local and national safety regulations. Unauthorized repairs could cause injury or appliance damage. The manufacturer cannot be held responsible for unauthorized work. The burner does not ignite after several attempts. Possible fault Solution The burner is not assembled correctly.

  • Page 19: Technical Service

    Miele Service department, Extended Service Contracts offered by other providers for Miele products will not be recognized by Miele. Our goal is to prevent unauthorized (and untrained) service personnel from working on your Miele products, possibly doing further damage to them, you and/or your home.

  • Page 21: Installation Instructions

    Installation Instructions IMPORTANT: SAVE FOR THE LOCAL ELECTRICAL INSPECTOR'S USE To prevent accidents and machine damage read these instructions before installation or use.

  • Page 22: Important Safety Instructions

    (3.5 kPa). This appliance must be installation in these applications. Please isolated at test pressures equal to or contact the Miele Technical Service less than ½ psi (3.5 kPa). Department with specific requirements. The combiset must not be installed...

  • Page 23

    IMPORTANT SAFETY INSTRUCTIONS Safety distances above the appliance The minimum safety distance given by the hood manufacturer must be maintained between the combiset and the hood above it. See the installation instructions of the hood for these safety measurements. If the hood manufacturers instructions are not available or if flammable objects are installed over the combiset (e.g.

  • Page 24

    (50mm) 2" (50 mm) CS 1112 CS 1122 CS 1212 CS 1221 CS 1223 CS 1326 CS 1411 not recommended 6" (150 mm) CS 1312 CS 1322 CS 1421 10" (250 mm) CS 1011 CS 1012 CS 1028 not allowed...

  • Page 25: Installation

    Installation Safety distance when installing the appliance near a wall with trim or a back splash A minimum distance of 2" (50 mm) between the trim or back splash and the countertop cut-out if required. This distance is only necessary if these items are made of combustible materials e.g.

  • Page 26: Installation Dimensions

    Installation Installation dimensions a Spring clips b Appliance front c Installation height d Power supply box with connection cable, L = 78 3/4" (2000 mm) e Gas fitting...

  • Page 27: Cut Out

    Installation Cut out If during installation the seal around the frame does not sit flush with the ^ Make the countertop cut-out for one countertop in the corners, the corner or more appliances as applicable. radius, maximum " (4 mm), can be Remember to maintain a minimum carefully filed down to fit.

  • Page 28: Installation Of Multiple Appliances

    Installation Installation of multiple appliances When installing more than one combiset appliance, a support bar b must be installed between the appliances. Countertop cut-out Countertop cut-out two appliances three appliances 6 " 6 " For the installation of three appliances For the installation of two appliances the width of the countertop cut-out D is the width of the countertop cut-out D is...

  • Page 29

    Installation Sample calculations for a countertop cut-out for three appliances appliance width appliance width appliance width Countertop minus 5/16" minus 5/16" cut-out (8 mm) (8 mm) 11" (280 mm) 11 5/16" (288 mm) 11" (280 mm) 33 5/16" (848 mm) 11"...

  • Page 30

    Installation " 3 / 1 6 1 " - 1 0 m m ( 2 5 - 3 2 " 2 " ( 5 0 m ( 5 0 m 2 " 2 " " 3 / 1 6 ( 5 0 m ( 5 0 m 6 "...

  • Page 31: Attach The Spring Clips And Support Bars

    Installation Attach the spring clips and support bars Wood or solid surface countertops Granite countertop " 3 / 1 6 " 3 / 1 6 1 " - 1 1 " - 1 0 m m 0 m m ( 2 5 - 3 ( 2 5 - 3 ^ Place the supplied spring clips a ^ Position and attach the spring clips...

  • Page 32

    Installation ^ Coat the edges of the spring clips, ^ and the space d between the strips and the countertop with silicone (supplied).

  • Page 33: Installing The Appliance

    Installation Installing the appliance ^ Feed the power cord down through the cut-out. ^ Then place the front side of the appliance in the countertop cut-out. ^ Then with a hand on each side of the appliance press down evenly on the edges until it clicks into position.

  • Page 34: Sealing

    Installation Sealing The appliance must not be permanently sealed into the countertop when installed. The sealing strip under the edge of the appliance provides a sufficient seal for the countertop. If the appliance is sealed into position, the countertop or appliance could be damaged if it needs to be removed for maintenance or service.

  • Page 35: Electrical Connection

    Electrical connection This appliance must be grounded This appliance is equipped with a according to local or national codes. three-prong grounding plug to prevent shock hazards. It should be All electrical work should be plugged directly into a properly performed by a qualified electrician grounded outlet.

  • Page 36

    Electrical connection Wiring Diagram...

  • Page 37: Gas Connection

    Gas connection Installation and service must be The gas connection must be made performed by a qualified installer, in accordance with local codes or, in service agency or the gas supplier. the absence of local codes, with In Massachusetts a licensed the National Fuel Gas Code, plumber/gas fitter is required.

  • Page 38: Gas Pressure Regulator

    - 4" w.c. LP gas - 10" w.c. Do not use any regulator unless it has been supplied by Miele. Doing so may cause a gas leak. If there is any doubt concerning installation contact the Miele Technical Service Department.

  • Page 39: Nominal Ratings

    Gas connection Nominal ratings Maximum output Gas type BTU/hr Natural Gas (NG) 27,600 Liquid Gas 22,200 (Propane) (LP) Minimum output Gas type BTU/hr Natural Gas (NG) 5,700 1.67 Liquid Gas 5,700 1.67 (Propane) (LP)

  • Page 40: Converting To Another Type Of Gas

    If the appliance is to be connected to a type of gas other than it was originally configured for, both the regulator and burner must be converted. A conversion kit is available as an optional accessory from the Miele Technical Service Department.

  • Page 41: Help Protect Our Environment

    Help protect our environment Disposal of packing materials Disposal of an old appliance The cardboard box and packing Old appliances contain materials that materials are biodegradable and can be recycled. Please contact your recyclable. Please recycle. local recycling authority about the possibility of recycling these materials.

  • Page 44

    Alteration rights reserved / 2608 M.-Nr. 07 369 720 / 00 For the most updated manual see the Miele web site.

Comments to this Manuals

Symbols: 0
Latest comments: