Summary of Contents for Jacuzzi SALON SPA BATH SERIES
Page 1
SALON™ SPA BATH SERIES INSTALLATION AND OPERATION INSTRUCTIONS Jacuzzi Luxury Bath ® 14525 Monte Vista Avenue Chino, CA 91710 1-800-288-4002 www.jacuzzi.com HD91000...
Save these instructions for future use. Use the form below to record your model and serial number for future reference. Date Purchased Purchased From Installed By Serial Number Model Installer: Leave the manual for the homeowner. Homeowner: Read this manual and keep for future reference. Installation and Operation Page 3 www.jacuzzi.com...
This is a professional grade product. A knowledge of construction techniques, plumbing and electrical installation according to codes are required for proper installation and user satisfaction. We recommend that a licensed contractor perform the installation of all Jacuzzi® Luxury Bath products. Our warranty does not cover improper installation related problems. CAUTION: When using this unit, basic precautions should always be performed, including the following: •...
It is the responsibility of the installer/owner to determine specific local code compliance prior to installation of the product. The Company makes no representation or warranty regarding, and will not be responsible for any code compliance. Product specifications are subject to change without notice. Installation and Operation Page 5 www.jacuzzi.com...
All bathtub units are factory tested for proper operation and watertight connections prior to shipping. However, the unit must be retested by the installer prior to installation. Jacuzzi Luxury Bath is not responsible for any defect that could have been discovered, repaired, or avoided by following this inspection and testing procedure: Place the bathtub on a level surface, near appropriate electrical supply, water supply, and water drainage.
Framing A technical specifications manual has been included with your bathtub. The Technical Specifications Manual will contain pertinent information regarding your Jacuzzi Luxury Bath product. Locate the Technical Specifications Manual at this time. Frame out the space where the bathtub is to be located. The...
Page 8
Specifications Manual that corresponds with your bathtub. Make appropriate cuts to the subfloor to accommodate the drain. Jacuzzi’s Tru-Level™ base is a standard feature on all bathtubs. If the subfloor is level and a continuous surface, no other preparation is necessary. Proceed to the “Installation” section.
PVC 45 Elbow Street Watertight installation of the drain and overflow is the installer’s responsibility. Drain leakage is excluded from the Jacuzzi Luxury Bath warranty of PVC Flex Pipe this product PVC 45 Elbow PVC Flex Pipe PVC 45 Elbow...
Page 10
Lower the control panel into the cutout and press firmly Inside of Bathtub to embed the adhesive (Figure 7). Connect the wire to the control box. Please proceed to Step 3 in the Drop-In Installation Figure 7 - Control Panel section. Page 10 Installation and Operation www.jacuzzi.com...
Push the GFCI test button in to reset. If the interrupter fails to operate in this manner, there is a ground current flowing or a device malfunction, indicating the possibility of electrical shock. Turn OFF power and do not use the bathtub until the source of the problem has been identified and corrected. Installation and Operation Page 11 www.jacuzzi.com...
Page 12
Sensor 240VAC Pump Inside Inside Ambient LOGO Panel Blower Light 2 Light 4 Light 2 Light Blower Lead Connectors 4 - Green (GRD) 3 - Red (L) 2 - Black (H) Heater View A Page 12 Installation and Operation www.jacuzzi.com...
Proper installation of the spout plumbing and compliance with local codes are the responsibility of Mortar or the installer. Jacuzzi Luxury Bath does not warrant Adhesive connections of water supply fittings and piping, fill systems, or drain/overflow systems. Nor is it...
Page 14
Floating Caulk around the perimeter of bathtub to seal Floor Compound the space between the rim and the finished deck Uneven Subfloor (Figure 8 on previous page). Figure 12 Page 14 Installation and Operation www.jacuzzi.com...
Meguiar’s #10 Mirror Glaze. If that is not available, use automotive rubbing compound followed by an application of automotive paste wax. • Major scratches and gouges which penetrate the acrylic surface will require refinishing. Call Jacuzzi Luxury Bath to find a service agent in your area. Installation and Operation Page 15 www.jacuzzi.com...
Salon™ Spa Bath General Operation Information All bathtubs manufactured by Jacuzzi Luxury Bath are designed for “fill and drain,” which means the bathtub should be drained after each use and filled with fresh water by the next bather. This is a health precaution, as these bathtubs are not designed to hold water continuously like pools or spas.
Page 17
Press the (+) or (-) button while in wave mode to set the maximum intensity level from 50% - 100%. There is a 5 second delay after adjusting the maximum intensity level before changes are observed. Installation and Operation Page 17 www.jacuzzi.com...
1 second and then stop. YOU MUST SET THE DAILY PURGE UPON INSTALLATION; THE DEFAULT IS NO PRE-SET DAILY PURGE. If a power failure occurs, the system will default to no daily purge cycle. Page 18 Installation and Operation www.jacuzzi.com...
The indicator lights immediately to the left and right of the air valve buttons indicate the amount of air induced (show images of max = 4 lights and off = 1 light). Installation and Operation Page 19 www.jacuzzi.com...
Controlling Whirlpool Direction and Flow Direction - All Jacuzzi jets, except the rotating neck jets, can be driectionally adjusted. To change the direction of the water flow, swivel the jet nozzle to the desired angle. The jets can be directed individually toward any location on your body to provide a hydromassage.
For best results, however, we recommend that you clean your whirlpool bathtub after each use using, Systems Clean™, our exclusive two-part plumbing system cleaner made specifically for whirlpool bathtubs. Systems Clean™ is available through an authorized Jacuzzi Whirlpool Bath Distributor or by calling us direct at 1-800-288-4002.
Minor scratches which do not penetrate the color finish can be removed by lightly sanding with 600-grit wet/dry sandpaper. Restore the gloss using Meguiar’s Mirror Glaze or automotive paste wax. Major scratches and gouges which penetrate the acrylic surface will require refinishing. Call Jacuzzi Luxury Bath to find a service agent in your area. Spinning Jet Maintenance If hair, or other types of debris, get caught in the bearings of these jets, it could cause them to stop spinning.This...
If the unit is within the warranty period, contact Jacuzzi Whirlpool Bath Service Support at 1-800-288-4002 with your bath’s serial number before work is started. The serial number is located on the Specification/Serial Number Plate (see the following page).
If you need a referral for a service company near you, or need assistance with operation or maintenance-related questions, please call our Service Support Department at 1-800-288-4002. Visit our web site at http://www.jacuzzi.com/ for products, services, and an online copy of these Installation and Operation Instructions.
ALLOWED BY LAW. NOTICE: This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. There are no warranties applicable to Jacuzzi Luxury Bath products except as expressly stated herein or as implied by applicable state and federal laws. The Company will not be responsible for any statements or representations made in any form that go beyond, are broader than or are inconsistent with any authorized literature or specifications furnished by the Company.
Page 26
The attached Warranty Registration MUST be filled out by the purchaser within thirty (30) days from purchase and received by Jacuzzi Luxury Bath in order for this warranty to become effective.
Page 27
Salon™ Spa Bath SALÓN™ DE BAÑERA DE HIDROMASAJE SERIE INSTRUCCIONES PARA LA INSTALACIÓN Y EL FUNCIONAMIENTO Jacuzzi Luxury Bath ® 14525 Monte Vista Avenue Chino, CA 91710 1-800-288-4002 www.jacuzzi.com HD91000 Installation and Operation Page 27 www.jacuzzi.com...
Fecha de la compra Comprado a Instalado por Número de serie Modelo Instalador: Deje el manual para el propietario. Propietario: Lea este manual y consérvelo para referencia futura. Installation and Operation Page 29 Instalación y Funcionamiento www.jacuzzi.com...
Éste es un producto de calidad profesional. Se requieren conocimientos de técnicas de construcción, fontanería e instalación eléctrica conforme a los códigos para la instalación apropiada y la satisfacción del usuario. Recomendamos que un contratista matriculado realice la instalación de todos los productos Jacuzzi® Luxury Bath. Nuestra garantía no cubre problemas relacionados con instalaciones inadecuadas.
La empresa no realiza manifestaciones ni ofrece garantías con respecto al cumplimiento de ningún código, ni será responsable de dicho cumplimiento. Las especificaciones del producto están sujetas a cambio sin previo aviso. Installation and Operation Instalación y Funcionamiento Page 31 www.jacuzzi.com...
Los daños o defectos en el acabado reclamados después de la instalación de la bañera están excluidos de la garantía. La responsabilidad de Jacuzzi Luxury Bath por daños durante el transporte finaliza contra entrega de los productos en buen estado al transportista.
Estructura Se ha incluido un Manual de especificaciones técnicas con su bañera. El Manual de especificaciones técnicas incluirá la información importante relacionada a su producto Jacuzzi Luxury Bath. Haga uso del Manual de especificaciones técnicas en este momento. Ubicaciones comunes de acceso Enmarque el espacio donde colocará...
Page 34
Realice los cortes adecuados en el contrapiso para ubicar el drenaje. La base Tru-Level™ de Jacuzzi es una características estándar en todas las bañeras. Si el contrapiso está nivelado y tiene una superficie continua, no es necesario realizar otra preparación. Vaya a la sección “Instalación”.
La instalación hermética del agua de drenaje y Codo de 45, el sistema contra desbordes es responsabilidad del instalador. La pérdida del drenaje no está incluida en la garantía Jacuzzi Luxury Bath de este Tubo flexible, producto. Codo niple de 45,...
Page 36
(Figura 7). bañera Conecte el cable con la caja de control. Vaya al Paso 3 en la sección de Instalación Figura 7 - Panel de control empotrada. Page 36 Instalación y Funcionamiento Installation and Operation www.jacuzzi.com...
DESCONECTE la alimentación y no utilice la bañera hasta haber identificado y corregido el origen del problema. Installation and Operation Instalación y Funcionamiento Page 37 www.jacuzzi.com...
Page 38
2 ambiental Sensor Generador de burbujas de aire Conectores de electrodos 4 - Verde (GRD) 3 - Rojo (L) Calentador 2 - Negro (H) 1 - Blanco (C) Vista A Page 38 Instalación y Funcionamiento Installation and Operation www.jacuzzi.com...
La instalación impermeable del drenaje es Mortero o adhesivo responsabilidad del instalador. La pérdida del drenaje no está incluida en la garantía Jacuzzi Luxury Bath de este producto. Sellador Instale el grifo en este momento. Se recomienda que el grifo sea instalado por un fontanero calificado.
Page 40
GFCI y compruebe el funcionamiento del sistema. Figura 12 Cierre las junturas de alrededor del perímetro de la bañera para sellar el espacio entre el borde y la plataforma terminada. Page 40 Instalación y Funcionamiento Installation and Operation www.jacuzzi.com...
• Será necesario volver a aplicar el acabado si los rayones y estrías penetran en la superficie acrílica. Llame a Jacuzzi Luxury Bath para localizar a un agente de servicio cercano a su domicilio. Instalación y Funcionamiento Installation and Operation Page 41 www.jacuzzi.com...
Salón™ de Bañera de Hidromasaje Salon™ Spa Bath Información general sobre el funcionamiento All bathtubs manufactured by Jacuzzi Luxury Bath are Todas las bañeras fabricadas por Jacuzzi Luxury Bath están diseñadas para “llenar y drenar”, lo que significa que se debe vaciar la bañera después de cada uso y llenarla con agua limpia para el próximo baño.
Page 43
Oprima el botón (+) o (-) mientras esté en modo de olas para ajustar el nivel de intensidad máxima de 50% a 100%. Hay una demora de 5 segundos después de regular el nivel de intensidad máxima antes de observar algún cambio. Installation and Operation Instalación y Funcionamiento Page 43 www.jacuzzi.com...
Debe establecer la PURGA TODOS LOS DIAS después de la instalación, el valor predeterminado es NO TODOS LOS DIAS PURGA PRE-SET. Si un fallo de corriente, el sistema por defecto a no ciclo de purga diaria. Page 44 Instalación y Funcionamiento Installation and Operation www.jacuzzi.com...
(sin aire) a la posición de abierto. Las luces indicadoras mostrarán el flujo a medida que pasa de mínimo a máximo. Para desactivar el modo de olas, pulse el botón (de ola). Installation and Operation Instalación y Funcionamiento Page 45 www.jacuzzi.com...
Control de la dirección y del flujo Whirlpool Dirección: Todos los chorros Jacuzzi, excepto los giratorios para el cuello, se pueden ajustar de modo direccional. Para cambiar la dirección del flujo del agua, gire la boquilla de chorro hasta el ángulo deseado.
600. Restaure el brillo con Mirror Glaze de Meguiar o con cera en pasta para automóviles. Será necesario volver a aplicar el acabado si los rayones y estrías penetran en la superficie acrílica. Llame a Jacuzzi Luxury Bath para localizar a un agente de servicio cercano a su domicilio.
Page 48
Es un dispositivo de seguridad y siempre debe estar colocado en el accesorio de succión para minimizar el riesgo posible de que el cabello o alguna parte del cuerpo queden atrapados. Page 48 Instalación y Funcionamiento Installation and Operation www.jacuzzi.com...
Si la unidad aún se encuentra dentro del período de la garantía, comuníquese con Asistencia de Servicio Técnico de Jacuzzi Whirlpool Bath llamando al 1-800- 288-4002 y verifique el número de serie de su bañera antes de que se inicie el trabajo. El número de serie está ubicado en la placa de Especificaciones/número de serie (consulte la página siguiente).
UTILICE EL MANUAL DE ESPECIFICACIONES TÉCNICAS PROVISTO CON EL PRODUCTO. Jacuzzi® Luxury Bath ha obtenido los listados de los códigos (normas) aplicables que suelen estar disponibles a nivel nacional para productos de este tipo. Es responsabilidad del instalador o propietario determinar el cumplimiento de los códigos locales específicos antes de instalar el producto.
AVISO: La presente garantía le otorga derechos legales específicos, y es posible que usted goce de otros derechos que varían de un estado a otro. No existen garantías que se apliquen a los productos Jacuzzi Luxury Bath excepto las estipuladas expresamente en la presente o las implícitas en las leyes estatales y federales pertinentes.
Page 52
También puede completar el registro que se encuentra abajo y enviarlo por correo a Jacuzzi a la dirección indicada a continuación. Para que esta garantía entre en vigencia, el comprador DEBE llenar el Registro de la garantía que se adjunta en un plazo de treinta (30) días a partir de la compra, y Jacuzzi Luxury Bath debe recibirlo.
Page 53
Salon™ Spa Bath SÉRIE DE BAIGNOIRES SALON™ SPA DIRECTIVES D’INSTALLATION ET D’UTILISATION Jacuzzi Luxury Bath ® 14525 Monte Vista Avenue Chino, CA 91710 1-800-288-4002 www.jacuzzi.com Installation and Operation Page 53 HD93000 www.jacuzzi.com...
Date d’achat Acheté chez Installé par Numéro de série Modèle Installateur : laissez le manuel au propriétaire. Propriétaire : lisez ce manuel et gardez-le pour consultation future. Installation et fonctionnement Page 54 Installation and Operation www.jacuzzi.com...
électrique conformes aux codes sont requises pour effectuer une installation adéquate à la satisfaction de l’utilisateur. Nous vous recommandons d’obtenir les services d’un entrepreneur agréé pour effectuer l’installation des produits Jacuzzi® Luxury Bath. Notre garantie ne couvre pas les problèmes causés par une mauvaise installation.
L’entreprise n’effectue aucune représentation ou garantie relatives à la conformité au code et elle ne sera pas responsable de cette dernière. Les spécifications du produit peuvent être modifiées sans préavis. Installation et fonctionnement Page 56 Installation and Operation www.jacuzzi.com...
La responsabilité de Jacuzzi Luxury Bath quant aux dommages causés par l’expédition prend fin au moment de la livraison au transporteur de produits en bon état.
Cadrage Un manuel de spécifications techniques est offert avec votre baignoire. Le manuel de spécifications techniques comprend des renseignements utiles concernant votre produit Jacuzzi Luxury Bath. Localisez le manuel de spécifications techniques. Encadrez l’espace où sera installée la baignoire. Considérez Emplacements d’accès communs...
Page 59
Effectuez les coupes appropriées dans le sous-plancher pour accommoder l’évacuation. La base Tru-Level™ de Jacuzzi est une caractéristique standard sur toutes les baignoires. Si le sous-plancher est une surface continue de niveau, aucune autre préparation n’est requise. Procédez à la section «...
L’installateur est responsable de l’étanchéité de l’installation de l’évacuation et du trop-plein. Toute Coude de 45° fuite de l’évacuation est exclue de la garantie en PVC Jacuzzi Luxury Bath de ce produit. Conduite flexible en PVC Coude mixte de 45° en PVC Assemblage de l’évacuation à...
Page 61
(figure 6). Reliez le fil à la boîte de commande. Figure 7 - panneau de commande passer à l’étape 3 dans la section Installation par le dessus. Installation et fonctionnement Installation and Operation Page 61 www.jacuzzi.com...
à la terre qui circule ou une défaillance de l’appareil, indiquant la possibilité d’une décharge électrique. Arrêtez l’appareil et n’utilisez pas la baignoire avant que la source du problème n’ait été identifiée et corrigée. Installation et fonctionnement Page 62 Installation and Operation www.jacuzzi.com...
Page 63
4 d’ambiance 2 intérieure 2 Ventilateur Connecteurs 4 – vert (mis à la terre) 3 – rouge (L) 2 – noir (H) Appareil de chauffage Vue A Installation et fonctionnement Installation and Operation Page 63 www.jacuzzi.com...
L’installateur est responsable de l’étanchéité de l’installation de l’évacuation. Toute fuite de Solin l’évacuation est exclue de la garantie Jacuzzi Luxury Bath de ce produit. Installez maintenant le robinet. Nous Agent recommandons de faire installer le robinet par un d’étanchéité...
Page 65
Figure 12 Calfeutrez autour du périmètre de la baignoire pour sceller l’espace entre le rebord et le support fini (figure 8 à la page précédente). Installation et fonctionnement Installation and Operation Page 65 www.jacuzzi.com...
à polir automobile suivie de l’application d’une cire automobile en pâte. • Les égratignures et les rainures majeures qui pénètrent la surface acrylique devront être finies à nouveau. Communiquez avec Jacuzzi Luxury Bath pour trouver un agent de service dans votre région. Installation et fonctionnement Page 66 Installation and Operation www.jacuzzi.com...
Baignoires Salon™ Spa Salon™ Spa Bath Renseignements généraux sur l’utilisation Toutes les baignoires fabriquées par Jacuzzi Luxury Bath sont conçues pour « remplissage et évacuation », ce qui signifie que la baignoire doit être vidée après chaque utilisation et remplie d’eau fraîche par le baigneur suivant.
Page 68
50 et 100 %. Il y a un délai de cinq secondes après le réglage du niveau maximum d’intensité avant que les changements soient remarqués. Installation et fonctionnement Page 68 Installation and Operation www.jacuzzi.com...
Vous devez définir la PURGE QUOTIDIEN Lors de l’installation; le défaut est sans purge PRE-SET QUOTIDIEN. Si une panne de courant survient, le système par défaut à aucun cycle de purge quotidienne. Installation et fonctionnement Installation and Operation Page 69 www.jacuzzi.com...
à la gauche du bouton de jet doivent être illuminés). Les robinets d’air droit et gauche passent simultanément de la position fermée (pas d’air) à la position ouverte. Les voyants lumineux afficheront le débit lorsqu’il passe du minimum au maximum. Page 70 Installation and Operation www.jacuzzi.com...
à tourbillon complet. Force de l’eau – le débit de la plupart des jets Jacuzzi peut être ajusté. Pour une Jets à plusieurs directions action robuste, augmentez la force du débit en tournant la buse, ou façade, vers la gauche (sens antihoraire).
Systems Clean™ notre nettoyant pour plomberie en deux parties exclusif conçu spécialement pour les bains tourbillons. Systems Clean™ est offert par les distributeurs de bains tourbillons Jacuzzi autorisés ou en composant directement le 1-800-288-4002. Additifs pour baignoire N’utilisez pas des additifs pour baignoire à...
600 grains. Restaurez le lustre au moyen de Meguiar’s Mirror Glaze ou d’une cire automobile en pâte. Les égratignures et les rainures majeures qui pénètrent la surface acrylique devront être finies à nouveau. Communiquez avec Jacuzzi Luxury Bath pour trouver un agent de service dans votre région Entretien des jets rotatifs Si des cheveux ou d’autres types de débris se prennent...
Si l’unité est encore couverte par la garantie, communiquez avec le service technique de Jacuzzi Whirlpool Bath au 1-800-288-4002 avec le numéro de série de votre baignoire avant d’effectuer toute réparation. Le numéro de série est situé sur la plaque de spécifications/numéro de série (reportez-vous à la page suivante).
Si vous avez besoin d’une référence pour une entreprise de service près de chez vous ou si vous avez des questions concernant le fonctionnement ou l’entretien, veuillez communiquer avec notre service à la clientèle au 1-800-288-4002. Visitez notre site Web à http://www.jacuzzi.com pour les produits, les services et une copie en ligne de ces directives d’installation et d’utilisation.
COUVERTURE DE LA GARANTIE Jacuzzi Luxury Bath (« l’Entreprise ») offre la garantie limitée à vie expresse suivante à l’acheteur original des produits Jacuzzi® Luxury Bath offerts au sein des collections Comfort, Comfort Plus, Pure Air®, Pure Air® II et Luxury™ (« Baignoire ») qui a acheté la Baignoire pour un usage personnel ou unifamilial résidentiel («...
Page 77
Ou encore, vous pouvez aussi enregistrer votre produit en remplissant la fiche ci-dessous et en l’envoyant à Jacuzzi à l’adresse indiquée. L’enregistrement de garantie ci-joint DOIT être rempli par l’acheteur dans un délai de trente (30) jours de l’achat et reçu par Jacuzzi Luxury Bath afin que cette garantie soit en vigueur.
Need help?
Do you have a question about the SALON SPA BATH SERIES and is the answer not in the manual?
Questions and answers