A.O. Smith DRE 52 Instructions Manual

A.O. Smith DRE 52 Instructions Manual

Commercial electric water heaters conversion kit
Hide thumbs Also See for DRE 52:
Table of Contents

Advertisement

Available languages

Available languages

FOR INSTALLATION BY QUALIFIED SERVICE PERSONNEL ONLY
CONVERSION KIT INSTRUCTIONS
Models DRE & DVE 52, 80, & 120
Commercial Electric Water Heaters
Series 100
CAUTION
TEXT PRINTED OR OUTLINED IN RED CONTAINS
INFORMATION RELATIVE TO YOUR SAFETY.
P L E A S E R E A D T H O R O U G H LY B E F O R E
500 Tennessee Waltz Parkway
ATTEMPTING ANY CONVERSION.
Ashland City, TN 37015
1-800-433-2545
www.hotwater.com
PRINTED IN U.S.A. 1008
196678-002
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the DRE 52 and is the answer not in the manual?

Questions and answers

Summary of Contents for A.O. Smith DRE 52

  • Page 1 FOR INSTALLATION BY QUALIFIED SERVICE PERSONNEL ONLY CONVERSION KIT INSTRUCTIONS Models DRE & DVE 52, 80, & 120 Commercial Electric Water Heaters Series 100 CAUTION TEXT PRINTED OR OUTLINED IN RED CONTAINS INFORMATION RELATIVE TO YOUR SAFETY. P L E A S E R E A D T H O R O U G H LY B E F O R E 500 Tennessee Waltz Parkway ATTEMPTING ANY CONVERSION.
  • Page 2: Table Of Contents

    FOREWORD The purpose of this manual is to explain how to change the voltage and wattage of your commercial electric water heater by changing the elements. This manual is not intended to explain the rebuilding of commercial electric water heaters in the field.
  • Page 3: Conversion Guidelines

    CONVERSION GUIDELINES Be sure to read and understand the conversion limitations and instructions prior to conversion. 1. No addition or substraction of heating elements are allowed in the conversion process; 2. Conversion kits are designed for specific voltage with Delta configuration, no other configuration or voltage is allowed;...
  • Page 4: Conversion Instructions

    CONVERSION INSTRUCTIONS REQUIRED ABILITY CONVERSION OF ANY WATER HEATER LISTED IN THIS MANUAL REQUIRES ABILITY EQUIVALENT TO THAT OF A LICENSED ELECTRICAL TRADESMAN INTRODUCTION Satisfying a customer order for a commercial electric heater from inventory may require modification to the KW input, the voltage, or the phase.
  • Page 5: Phase Conversion

    IMMERSION THERMOSTAT MODEL TRANSFORMER IMMERSION THERMOSTAT MODEL TRANSFORMER CONNECTION TABLES Volts Line On Load on Common & 208 Common & 240 Secondary Common & 277 120V Common & 480 V. PHASE CONVERSION IMMERSION THERMOSTAT MODEL SINGLE PHASE TERMINAL BLOCK A. IMMERSION THERMOSTAT MODEL THREE PHASE TO SINGLE PHASE 1.
  • Page 6: Caution

    C. SURFACE THERMOSTAT MODEL SURFACE THERMOSTAT MODEL SINGLE PHASE TERMINAL BLOCK THREE PHASE TO SINGLE PHASE 1. Disconnect blue wires from terminal L-2. 2. Connect all blue wires to terminal L-1 (with black wires). 3. Disconnect all red wires from terminal L-3. 4.
  • Page 7: Check List

    The voltage, element KW, total KW data of the rating plate must be modified by covering them with the label provided in the conversion kit. Be sure the new ratings on the label match the conversion you have just completed. Peel off the back of the label and paste over the four lines as shown on the revised rating plate below.
  • Page 8 ELEMENT SIZE VERIFICATION All elements are marked with both wattage and voltage. Verification can be made by measuring the ohms resistance across the terminals of the elements. Element must be disconnected from the circuit. The following table gives resistance in ohms for all elements used in commercial electric water heaters. OHMS RESISTANCE TABLE VOLTAGE WATTAGE...
  • Page 9 NOTES...
  • Page 10 500 Tennessee Waltz Parkway Ashland City, TN 37015 1-800-433-2545 www.hotwater.com...
  • Page 11 INSTALLATION PAR DES SPÉCIALISTES QUALIFIÉS UNIQUEMENT INSTRUCTIONS TROUSSE DE CONVERSION Modèles DRE et DVE 52, 80 et 120 Chauffe-eau électriques commerciaux Série 100 ATTENTION LE TEXTE EN ROUGE OU ENCADRÉ DE ROUGE VISE À ASSURER LA SÉCURITÉ DES UTILISATEURS. IL FAUT DONC LE LIRE 500 Tennessee Waltz Parkway ATTENTIVEMENT AVANT DE CONVERTIR LE Ashland City, TN 37015, États-Unis...
  • Page 12: Avant-Propos

    AVANT-PROPOS Le présent manuel vise à expliquer comment modifier la puissance nominale des chauffe-eau électriques commerciaux décrits ou leur circuit pour qu’ils fonctionnent à une autre tension d’alimentation. Son objectif n’est pas d’expliquer comment reconstruire un chauffe-eau électrique commercial sur place. L’ajout et la soustraction d’éléments chauffants sur place ne sont pas des pratiques approuvées par Underwriters Laboratories, Inc.
  • Page 13: Guide De Conversion

    GUIDE DE CONVERSION Avant de convertir un chauffe-eau, il faut lire et comprendre les instructions et les restrictions qui s’appliquent. 1. Il est interdit d’augmenter ou de réduire le nombre d’éléments chauffants; 2. Chaque trousse de conversion est conçue pour une tension d’utilisation en particulier et un circuit en configuration Delta;...
  • Page 14: Instructions De Conversion

    INSTRUCTIONS DE CONVERSION COMPÉTENCES REQUISES LA CONVERSION DES CHAUFFE-EAU DÉCRITS DANS LE PRÉSENT MANUEL EXIGE DES COMPÉTENCES ÉQUIVALENTES À CELLES D’UN ÉLECTRICIEN QUALIFIÉ INTRODUCTION Pour satisfaire un client qui commande un chauffe-eau commercial standard, il faut possiblement convertir sa puissance nominale ou la tension ou la phase à...
  • Page 15: Conversion De Phase

    TRANSFORMATEUR DES MODÈLES À CONNEXIONS DU TRANSFORMATEUR THERMOSTAT IMMERGÉ MODÈLES À THERMOSTAT IMMERGÉ Volts Connexions Tension Commune et 208 Circuit Commune et 240 secondaire Commune et 277 120 V Commune et 480 V. CONVERSION DE PHASE MODÈLES À THERMOSTAT IMMERGÉ BLOC DE CONNEXION A.
  • Page 16: Attention

    C. MODÈLES À THERMOSTAT MONTÉ EN SURFACE BLOC DE CONNEXION DES MODÈLES THERMOSTAT MONTÉ EN SURFACE CONVERSION D’UNE PHASE À TROIS PHASES ALIMENTATION MONOPHASÉE 1. Débrancher les fils bleus de la borne L2. 2. Brancher les fils bleus à la borne L1 (avec les fils noirs). 3.
  • Page 17: Liste De Vérification

    L’étiquette fournie dans la trousse de conversion indique la tension d’utilisation, la puissance des éléments et la puissance totale du chauffe-eau converti. Elle doit être collée sur la plaque signalétique d’origine. Il convient de s’assurer que les caractéristiques figurant sur l’étiquette correspondent à la conversion effectuée. Retirer le papier au verso de l’étiquette et la coller de façon à...
  • Page 18 VÉRIFICATION DES CARACTÉRISTIQUES DES ÉLÉMENTS La puissance et la tension d’utilisation sont indiquées sur chaque élément. Ces caractéristiques peuvent être confirmées par une simple mesure de la résistance électrique aux bornes de l’élément. Pour faire la mesure, il faut débrancher l’élément.
  • Page 19 NOTES...
  • Page 20 500 Tennessee Waltz Parkway Ashland City, TN 37015, États-Unis 1 800 433-2545 www.hotwater.com...

Table of Contents