Related Manuals for Husqvarna 324HDA55 X-series
Summary of Contents for Husqvarna 324HDA55 X-series
- Page 1 Operator’s manual (EPA) 324HDA55 X-series Please read the operator’s manual carefully and make sure you E E E E n n n n g g g g l l l l i i i i s s s s h h h h...
-
Page 2: Key To Symbols
Symbols WARNING! Incorrect or careless use of a hedge trimmer can turn it into a dangerous tool that can cause serious or even fatal injury. It is extremely important that you read and understand the contents of this operator’s manual. -
Page 3: Table Of Contents
YOUR WARRANTY RIGHTS AND OBLIGATIONS ... CONTENTS Note the following before starting: Husqvarna AB has a policy of continuous product development and therefore reserves the right to modify the design and appearance of products without prior notice. Long-term exposure to noise can result in permanent hearing impairment. -
Page 4: Safety Instructions
SAFETY INSTRUCTIONS Personal protective equipment IMPORTANT! You must use approved personal protective equipment whenever you use the machine. Personal protective equipment cannot eliminate the risk of injury but it will reduce the degree of injury if an accident does happen. Ask your dealer for help in choosing the right equipment. -
Page 5: Hand Guard
SAFETY INSTRUCTIONS Hand guard The hand guard prevents hands from coming into contact with the moving blades, for example, if the operator loses grip on the front handle. Vibration damping system Your machine is equipped with a vibration damping system that is designed to minimize vibration and make operation easier. -
Page 6: Checking, Maintaining And Servicing The Machine ' S Safety Equipment
• See instructions under the heading Start. Start the hedge trimmer and apply full throttle. Release the throttle trigger and check that the blades stop and remain stationary. If the blades move when the throttle trigger is in the idle position then the carburettor idle setting must be adjusted. - Page 7 SAFETY INSTRUCTIONS Muffler • Never use a machine that has a faulty muffler. • Regularly check that the muffler is securely attached to the machine. • If the muffler on your machine is fitted with a spark arrestor mesh this must be cleaned regularly. A blocked mesh will cause the engine to overheat and may lead to serious damage.
-
Page 8: General Safety Precautions
SAFETY INSTRUCTIONS General safety precautions IMPORTANT! The machine is only designed for cutting branches and twigs. Never use the machine if you are tired, if you have drunk alcohol, or if you are taking medication that could affect your vision, your judgement or your co-ordination. Wear personal protective equipment. -
Page 9: Safety Instructions When Using The Hedge Trimmer
SAFETY INSTRUCTIONS Safety instructions when using the hedge trimmer WARNING! The machine can cause serious personal injury. Read the safety instructions carefully. Learn how to use the machine. WARNING! Cutting tool. Do not touch the tool without first switching off the engine. -
Page 10: Basic Working Techniques
Do not rush the work, but work steadily until all the branches have been cut back cleanly. 10 – English Changing the hedge trimmer angle • Undo the knob. • Press the cutting head against the ground or some other solid object until the desired angle has been obtained. -
Page 11: What Is What
What is what? 1 Cutter 2 Grease nipples (3) 3 Bevel gear 4 Blade guard 5 Shaft 6 Front handle 7 Throttle control 8 Stop switch 9 Throttle lock 10 Cylinder cover 11 Starter handle 12 Fuel tank WHAT IS WHAT? 13 Choke control 14 Air purge 15 Air filter cover. -
Page 12: Assembly
English ASSEMBLY Fitting the cutting head It is important that the hedge trimmer is laid on a flat surface when you fit the cutting head. Otherwise the cutting head may not be fitted straight. 1 Fit the cutting head to the shaft. CAUTION! Make sure the drive shaft inside the shaft engages with the recess in the cutting head. -
Page 13: Fuel
When the machine is new the engine oil should be changed after the first month or after 10 hours of operation. • For the best result and function use HUSQVARNA engin oil. • When HUSQVARNA engine oil is not available another high grade engine oil can be used. -
Page 14: Starting And Stopping
STARTING AND STOPPING Check before starting • Inspect the working area. Remove any objects that could be thrown out. • Check the cutting attachment. Never use blades that are dull, cracked or damaged. • Check that the machine is in perfect working order. Check that all nuts and screws are tight. -
Page 15: Maintenance
Carburettor WARNING! The complete clutch cover and shaft must be fitted before the machine is started, otherwise the clutch can come loose and cause personal injury. Function • The carburettor governs the engine’s speed via the throttle control. Air and fuel are mixed in the carburettor. The air/fuel mixture is adjustable. -
Page 16: Air Filter
English MAINTENANCE Oiling the air filter Always use HUSQVARNA filter oil, art. no. 531 00 92-48. The filter oil contains a solvent to make it spread evenly through the filter. You should therefore avoid skin contact. Put the filter in a plastic bag and pour the filter oil over it. -
Page 17: Maintenance Schedule
Maintenance schedule Below you will find some general maintenance instructions. If you need further information please contact your service workshop. Daily maintenance • Check throttle trigger and throttle trigger lockout function. • Check that the stop switch works correctly. • Check that the blades do not move when the engine is idling or when the choke is in the start throttle position. -
Page 18: Technical Data Technical Data
Note 1: Equivalent noise pressure level is calculated as the time-weighted energy total for noise pressure levels under various working conditions with the following time distribution: 1/2 idle and 1/2 max. speed. ´®z+H:)¶5w¨ ´®z+H:)¶5w¨ 18 – English TECHNICAL DATA 324HDA55 1,53/25,0 1,38/35 1,03/26 3100 11000 0,8 / 7000... -
Page 19: Federal Emission Control Warranty Statement
The warranty period begins on the date small nonroad engine is delivered. LENGTH OF COVERAGE Husqvarna Forest & Garden warrants to the initial owner and each subsequent purchaser that the engine is free from defects in materials and workmanship which cause the failure of a warranted part for a period of two years. - Page 20 1140260-95 ´®z+H:)¶5w¨ ´®z+H:)¶5w¨ 2004-04-02...
Need help?
Do you have a question about the 324HDA55 X-series and is the answer not in the manual?
Questions and answers