Related Manuals for Hong Kong Easyweld Easytig 160S
Summary of Contents for Hong Kong Easyweld Easytig 160S
- Page 1 EasyTig Operation Manual Model: Easytig 160S/ 200S/ 180A/ 200A/ 200ADS/ 200P/ WS300/ WS400/ WSM300/ WSM400 Hong Kong Easyweld Limited...
-
Page 2: Table Of Contents
EC DECLARRATION OF CONFORMITY Hereby we declare that our machines for industrial and professional use as stated below Type: EasyTig 160S, 200S, 180A, 200A, 200ADS, Conform the EMC Directives: 73/23/EEC and 89/336/EEC European Standard: EN/1EC60974 Please read and understand this instruction manual carefully before the installation and operation of this equipment. -
Page 3: Warning
WARNING Welding and cutting is dangerous to the operator, people in or near the working area, and the surrounding, if the equipment is not correctly operated. Therefore, the performance of welding/cutting must only be under the strict and comprehensive observance of all relevant safety regulations. -
Page 4: General Description
The features of this product are as following: stable output, reliable, completely portable, efficient and low noise generated while welding is performed. -TIG welding is available for EasyTig 160S/200S. Both MMA and TIG are welding are available for EasyTig 180A/200A/200ADS/200P and WS 300/WS 400/WSM 300/WSM 400. -
Page 5: Main Parameter
MAIN PARAMETER Type EasyTig EasyTig EasyTig EasyTig TIG200P 160S 200S 180A 200A/200 Input volt (V) Single Phase AC22OV±15% Frequency (Hz) 50/60 50/60 50/60 50/60 50/60 Input current (A) No-load volt (V) Output current (A) 10~160 10~200 10~180 10~200 10~200 Rated Input (KVA) Post-flow Time (S) 3, 8 3, 8... - Page 6 MAIN PARAMETER Type WS 300 WS 400 WSM 300 WSM 400 Input voltage (V) 3 phase AC380V±15% Frequency (Hz) 50/60 50/60 50/60 50/60 Rated Input (KVA) No-load voltage (V) 10~300 10~400 10~300 10~400 Peak current (A) 10~300 10~400 Valley current (A) 0~10 0~10 Up Slope (S)
-
Page 7: Installation And Operation
The assembled length of main cables and torch cables is recommended. Easytig 160S/ 200S Easytig 180A/ 200A ‘ - ’ 2c/ ‘ + ’... - Page 8 Please note: Input voltage for EasyTig 160S, 200S, 180A, 200A, 200ADS, 200P is of 220V and single phase. Input voltage for WS 300/ WS 400/ WSM 300/ WSM 400 is of 380V and three phase.
- Page 9 2.2 MMA & TIG welding equipment : (Available for EasyTig 180A, 200A, 200ADS, 200P, WS 300, WS 400, WSM 300, WSM 400) ‘-’. Connect Torch welding cable into the fast-plug socket. a. Connect Torch Gas hose fitting into the connection point on the panel board.
- Page 10 Pilot lamp is on, in case that this welding equipment is of overheating protection status. Overheating arises if this welding equipment is overloaded. This welding equipment automatically restarts when the temperature inside of this welding equipment has fallen, and pilot lamp is off. 7.
-
Page 11: Speed-Read Table
CAUTIONS Possible threaten to the safety, and even life of operator and people in or near working area, and damage to this welding equipment occurs, in case of any disconnection of cable and plug during the welding operation. SPEED-READ TABLE Parameter for Stainless Plate TIG Welding (for reference only) Plate Connector... -
Page 12: Problem Possibly Occur
Parameter for Aluminum and its Alloy TIG Welding (for reference only) Plate Slope Welding Tungsten Wire Pre-Tempe Welding Nozzle thickness shape Layers Diameter Diameter rature (C) Current Volume Diamet (mm) (mm) (mm) (L/min) I-Shape 1.6~2.0 50~80 2~2.5 50~80 8~12 8~12 150~180 8~12 1~2/1... -
Page 13: Caution
CAUTIONS 1. Working Environment 1.1The location in which this welding equipment is installed should be of little dust, corrosive chemical gas, flammable gas or materials etc, and of maximum 80% humidity; 1.2Avoid the operation of welding in the open air unless the working area sheltered from the sun shining, rain water and snow etc;... -
Page 14: Troubleshooting
TROUBLESHOOTING CAUTIONS: Only the qualified technicians are authorized to undertake the repair task of this welding equipment in case of machine fault EasyTig 160S, 200S, 180A, 200A, 200AD, 200P Fault Symptoms Rectification 1. While this 1. Possible function failure of power switch. Compensate it welding if necessary. - Page 15 Fault Symptoms Rectification 1. Possible disconnection of welding torch cable. 4. While this 2. Possible disconnection of earth cable, or unavailability of welding connection of the earth cable and work piece. equipment 3. The connection between positive output terminal or the is operated, gas or electricity output terminal and this welding fault indicator...
- Page 16 Fault Symptoms Rectification 7. Unstable 1. Possible damage of 1K resistance. Replace it if current output necessary. during the 2. The connection of this welding equipment is not welding available. operation and potentiometer is unavailable. 8. Excessive plash 1. Misconnection of earth cable and welding torch cable. generated 2.
- Page 17 WS 300/ WS 400/ WSM 300/ WSM 400 Rectification Fault Symptoms 1. Possible failure of connection of power supply, check and 1. While this reconnect if necessary. welding 2. If power supply is available of input, possible damage of equipment is four thermal resistance.
- Page 18 Rectification Fault Symptoms 5. While this 1. It is possible of over-current protection status. Switch off welding the power supply, wait till the fault indicator is off, and equipment is restart this welding equipment. operated, the 2. It is possible of over-heating protection status. Wait till fault indicator the fault indicator is off, and the welding operation will is on, and...
Need help?
Do you have a question about the Easytig 160S and is the answer not in the manual?
Questions and answers