Table of Contents
Advertisement
8
System Maintenance
(cont'd)
2. Enter the control programming mode by following steps 1 - 5
of Adding Remote Controls to Your System .
3a. If you have only one remaining remote control, press the
LOCK button on that remote control four (4) times, pausing
at least 1 second in between each press. The horn must "honk"
each time you press the LOCK button.
3b. If you have two remaining remote controls, press the LOCK
button on each remote control two (2) times, pausing at least
1 second in between each press. The horn must "honk" each
time you press the LOCK button.
3c. If you have three remaining remote controls, press the
LOCK button on one remote control twice, then press the
LOCK button on the remaining remote control once. Pause at
least 1 second in between each press. The horn must "honk"
each time you press the LOCK button.
4. Turn the vehicle ignition off to exit the programming mode.
When you are finished, the lost or stolen remote control will
no longer operate your system.
Basic Troubleshooting
This section outlines some of the basic issues you may experience
This section outlines some of the basic issues you may experience
while becoming used to the F10/F15. If you have a problem that is not
covered by this section, please consult your installer.
S
S
S
S
S
y
y
y
y
y
m
m
m
m
m
p
p
p
p
p
o t
o t
o t
o t
o t
m
m
m
m
m
P
P
P
P
P
o r
o r
o r
o r
o r
b
b
b
b
b
e l
e l
e l
e l
e l
m
m
m
m
m
W
e
a
k
r o
d
R
e
m
o
e t
c
o
n
r t
l o
d
o
e
s
n
t o
w
o
k r
R
e
m
o
e t
c
p
o r
g
a r
m
m
D
o
r o
r o
o
e
t n
a r
n
c
e
S
s y
e t
m
w
l l i
n
t o
r a
m
C
o
r u
e t
y s
S
s y
e t
m
s i
m
o
d
e
S
S
S
S
S
l o
l o
l o
l o
l o
t u
t u
t u
t u
t u
o i
o i
o i
o i
o i
n
n
n
n
n
e
a
d
b
t a
e t
y r
C
h
a
n
g
e
b
t a
e t
y r
o
n
r t
l o
n
t o
P
o r
g
a r
m
e r
m
o
e t
e
d
c
o
n
r t
l o
p (
a
g
e
) 7
h t
r e
C
o l
s
e
e
t n
a r
n
c
e
s i
o
p
e
n
g i l
t h
s i
o
n
u T
n r
c
o
r u
e t
y s
g i l
t h
o
f f
n i
V
l a
t e
u T
n r
o
f f
V
l a
t e
m
o
d
e
p (
a
g
e
) 5
Emergency Disarm Procedure
If your remote control is lost or fails to function, use this procedure to
disarm the F10/F15 and start your vehicle.
1. Use the keys to enter the vehicle.
The alarm will sound once the door is opened.
2. Insert the key into the ignition and turn to the ON position.
3. Locate and press the emergency override button.
The alarm will turn off and then you will be able to
start your vehicle.
Your Emergency Disarm Button is located:
Installer Programmed Options
Ignition On Door Lock
ON
Ignition Off Door Unlock
ON
Siren/Horn Chirps
ON
Passive Arming
ON
9
OFF
OFF
OFF
OFF
Advertisement
Table of Contents
Need help?
Do you have a question about the F10 and is the answer not in the manual?
Questions and answers