Table of Contents
Advertisement
Crown Broadcast FME 350W to 2000W User Manual– 05/2013
NAME
INPUT.LINE1.LEVEL
INPUT.LINE1.PREAC
INPUT.LINE1.PRESENCE
INPUT.LINE1.RIGHT.PEAK
INPUT.LINE1.RIGHT.PKMAX
INPUT.LINE1.SW.BACKDELA
Y
INPUT.LINE1.SW.DELAY
INPUT.LINE1.SW.PRIO
INPUT.LINE1.SW.SILENCE
INPUT.LINE1.SW.THRESH
INPUT.LINE1.TRIM
INPUT.LINE1.TYPE
INPUT.LINE2.DRIVE
INPUT.LINE2.FLT
INPUT.LINE2.LEFT.PEAK
INPUT.LINE2.LEFT.PKMAX
INPUT.LINE2.LEVEL
INPUT.LINE2.PREAC
INPUT.LINE2.PRESENCE
INPUT.LINE2.RIGHT.PEAK
INPUT.LINE2.RIGHT.PKMAX
INPUT.LINE2.SW.BACKDELA
Y
INPUT.LINE2.SW.DELAY
INPUT.LINE2.SW.PRIO
INPUT.LINE2.SW.SILENCE
INPUT.LINE2.SW.THRESH
INPUT.LINE2.TRIM
INPUT.LINE2.TYPE
INPUT.MPX.SW.BACKDELAY
INPUT.MPX.SW.DELAY
INPUT.MPX.SW.THRESH
INPUT.MPX1.DRIVE
INPUT.MPX1.LEVEL
INPUT.MPX1.PEAK
INPUT.MPX1.PKMAX
Crown Broadcast, a division of International Radio & Electronics Corporation 25166 Leer Drive, Elkhart, Indiana, 46514-5425 USA
Access
Possible value on the
(R/W)
serial port of the unit
R/W
-20.00...18.00
R/W
0;50;75
"NONE" or "L" or "R" or
R
"L&R"
R
-100 ... 28
R
-100 ... 28
R/W
XXX=[0...30]
R/W
XXX=[1...120]
R/W
0..7 ; 0=disabled
"L" or "R" or "ANY" or
R/W
"BOTH"
R/W
-90...000
R/W
-3.00 to 3.00
R
"ANA" or "AES" "OFF"
R/W
-6.00 to 6.00
R/W
0;1;2 0=15;1=16;2=17
R
-100 ... 28
R
-100 ... 28
R/W
-20.00...18.00
R/W
0;50;75
"NONE" or "L" or "R" or
R
"L&R"
R
-100 ... 28
R
-100 ... 28
R/W
XXX=[0...30]
R/W
XXX=[1...120]
R/W
0..7 ; 0=disabled
"L" or "R" or "ANY" or
R/W
"BOTH"
R/W
-90...000
R/W
-3.00 to 3.00
R
"ANA" or "AES" "OFF"
R/W
XXX=[0...30]
R/W
XXX=[1...120]
R/W
-90...000
R/W
-6.00 to 6.00
R/W
-18.00...+18.00
R
-150...150
R
-150...150
Page 73
Ph +1 (574) 262 8900
Comments
Internal numerical gain. For AES, between -20 and
0; for ANA between -18 and +18
Sets the value of the pre-emphasis
Indicates audio signals are present on input 1
Gives the right audio input max peak value over 100
milliseconds
Gives the right audio input max peak value over 1
second.
Back delay on the channel with the highest
configurable priority.
Switching delay when loss of audio 1
Priority of each audio channel (7= highest priority)
Sets on which channel (L,R or L+R) silence
detection must be conducted for the audio input 1
Silence triggering level in dBFS on channel 1
Sets the offset between left and right channels (+3 =
left channel level is 3 dBu higher than right channel
level)
Indicates the type of audio signals present on input
1
Drive setting, allows an increase of the input audio
level without changing the deviation setting.
Configuration of the audio filter
Gives the right audio input max peak value over 100
milliseconds
Gives the right audio input max peak value over 1
second.
Internal numerical gain. For AES, between -20 and
0; for ANA between -18 and +18
Sets the value of the pre-emphasis
Indicates audio signals are present on input 2
Gives the right audio input max peak value over 100
milliseconds
Gives the right audio input max peak value over 1
second
Back delay on the channel with the highest
configurable priority.
Switching delay when loss of audio 2
Priority of each audio channel (7= highest priority)
Sets on which channel (L,R or L+R) silence
detection must be conducted for the audio input 2
Silence triggering level in dBFS on channel 2
Sets the offset between left and right channels (+3 =
left channel level is 3 dBu higher than right channel
level)
Indicates the type of audio signals present on input
2
Back delay on the channel with the highest
configurable priority.
Switching delay when loss on the MPX input
Silence triggering level in dBFS on MPX 1
Drive setting, allows an increase of the input audio
level without changing the deviation setting.
Internal numerical gain
Gives the deviation max peak value of the
transmitted signal in kHz over 100 milliseconds
Gives the deviation max peak value of the
transmitted signal in kHz over 1 second
Advertisement
Table of Contents
