Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Micon T20
- Page 1 MICON USB VoIP Switch User’s Guide T20/T30...
- Page 2 INTERNET AND DO NOT AND ARE NOT INTENDED TO SUPPORT OR CARRY EMERGENCY CALLS TO ANY TYPE OF HOSPITALS, LAW ENFORCEMENT AGENCIES, MEDICAL CARE UNIT OR ANY OTHER TYPE OF EMERGENCY SERVICES OF ANY KIND OVER THE INTERNET AND THAT MICON AFFILIATES,...
-
Page 3: Technical Specifications
1.2 Technical Specifications • USB port:1 • RJ11 port: 2 • LED: 3 (Power, In, OUT) • Size: 138 x 45 x 25 MM • Working temperature: 0- 60 • Working voltage: 5V • power: 0.5W (sleeping),1.5W (working) • Operating System: Windows’ 2000•XP 1.3 System Requirement •... -
Page 4: Hardware Installation
Unplug your telephone cord from the wall jack. Using the supplied telephone wire, connect one end to the “LINE” port of MICON T20/30, another to the wall jack as shown in Fig.1 Note: 1. PSTN service is required for VoIP call forwarding feature to function properly. -
Page 5: Phone Connection
Fig.2 Phone Connection 2.3 USB Connection Plug the MICON T20/30 to the USB port on your PC with the included USB cable as shown in Fig.3. The PC will load the necessary driver automatically*. The LED will be on once MICON T20/30 is connected properly. - Page 6 CD in the CDROM drive and follow the on screen instruction to install Skype**. 3.2 MICON VoIP Utility Installation Double click on the button “Driver for MICON T20/30” to launch MICON VoIP Utility installation program. Follow the on screen instruction to finish the installation.
- Page 7 4.1 Use MICON T20/30 to make a PSTN call MICON T20/30 is programmed to use PSTN line by default if a PSTN line is connected. So you can use your phone that is connected with MICON T20/30 to call a PSTN number or mobile phone number as you would on any regular phone.
- Page 8 ** Special service numbers such as international access codes are prohibited to be set into the speed-dial number. 3. Pick up the handset of the phone connected with MICON T20/30, press " " on the keypad of the phone, and the speed-dial number set in the previous step, then "#". The call will...
- Page 9 Fig.6 Skype Calls Note If MICON T20/30 is not connected with a PSTN line there is no need to dial “ ” first. You can directly dial the speed-dial number plus # (e.g. 22#). 4.3 How to receive calls When somebody calls your Skype or PSTN number, the phone connected to the MICON T20/30 will ring.
- Page 10 Fig.9 Enable Call Forwarding In some cases, the phone connected to your MICON T20/30 will ring one time before the forwarding process begins. It is important not to pick up the phone connected to your MICON T20/30. Otherwise, the call will not be forwarded. To avoid the Skype...
- Page 11 Fig.10a Disable Call Notification Fig.10b Disable Call Notification Note: If the MICON T20/30 is connected with PBX as an extension, you will need to use a special dialing format as following: xP123456790 where the first “x” is the code to access an outside line, “P” is a special symbol representing a pause of 2 seconds, and “1234567890”...
- Page 12 PSTN phones (Reverse Forwarding) on the T-30. Following the same process as in the last section you can set up the MICON VoIP utility so that it will automatically forward you call to a specific Skype contact or it will prompt you to enter the speed dial # for the contact you want to call.
-
Page 13: Select A Location
Sound Recording” to choose your original sound card as the playback or recording device. If you choose the later route, you will need to configure Skype to use the MICON T20/30 as the sound device by click on “Tools\Options\Sound Devices”... - Page 14 Skype as “Generic” Internet Phone audio device. So, your investment in MICON T20/30 is protected. ► Question 8. When I use the MICON T20/30, do I have to operate the keyboard or mouse? No. Actions of dialing on phone are simulated as the action of keyboard and mouse by MICON T20/30 utility software.
- Page 15 MICON T20/30 is designed as a single line device. To use it with a 2-line phone, a special line splitter is need to feed line 1 to the input of the MICON T20/30 and line 2 to the phone directly.