BATTERY
COVER
DISCARD
TERMINAL
PROTECTIVE
CAPS
HEX BOLT
POSITIVE CABLE
(RED)
INSTALL SEAT (See Fig. 3)
Adjust seat before tightening adjustment knob.
•
Remove adjustment knob and flat washer securing
seat to cardboard packing and set aside for assembly
of seat to tractor.
•
Pivot seat upward and remove from the cardboard pack-
ing. Remove the cardboard packing and discard.
•
Place seat on seat pan so head of shoulder bolt is
positioned over large slotted hole in pan.
•
Push down on seat to engage shoulder bolt in slot and
pull seat towards rear of tractor.
•
Pivot seat and pan forward and assemble adjustment
knob and flat washer loosely. Do not tighten.
•
Lower seat into operating position and sit on seat.
•
Slide seat until a comfortable position is reached which
allows you to press clutch/brake pedal all the way
down.
•
Get off seat without moving its ad just ed position.
•
Raise seat and tighten adjustment knob securely.
SEAT
SEAT PAN
AD JUST MENT KNOB
NOTE: You may now roll or drive your tractor off the skid.
Follow the ap pro pri ate instruction below to remove the
tractor from the skid.
WARNING: Before start ing, read, un der stand and fol low
all in struc tions in the Op er a tion section of this man u al. Be
sure tractor is in a well-ventilated area. Be sure the area in
front of tractor is clear of other peo ple and objects.
ASSEMBLY
NEGATIVE
CABLE
(BLACK)
KEPS
NUT
FIG. 2
SHOUL DER BOLT
FLAT
WASH ER
02464
FIG. 3
TO ROLL TRACTOR OFF SKID (See Op-
er a tion section for location and function of
con trols)
•
Press lift lever plunger and raise attachment lift lever
to its highest po si tion.
•
Release parking brake by de press ing clutch/brake
ped al.
•
Place freewheel control in "trans mis sion dis en gaged
position" (See "TO TRANS PORT" in the Op er a tion
section of this manual).
•
Roll tractor forward off skid.
•
Remove banding holding the deflector shield up against
tractor.
TO DRIVE TRAC TOR OFF SKID (See Op-
er a tion section for location and function of
con trols)
WARNING: Before start ing, read, un der stand and fol low
all in struc tions in the Op er a tion section of this man u al. Be
sure tractor is in a well-ventilated area. Be sure the area in
front of tractor is clear of other peo ple and objects.
•
Be sure all the above assembly steps have been com-
pleted.
•
Check engine oil level and fill fuel tank with gasoline.
•
Place freewheel control in "trans mis sion en gaged"
po si tion (see "TO TRANSPORT" in Op er a tion section
of this manual).
•
Sit on seat in operating position, depress clutch/brake
pedal and set the parking brake.
•
Place motion control lever in neutral (N) position.
•
Press lift lever plunger and raise attachment lift lever
to its highest position.
•
Remove key from bag and start the engine (see "TO
START ENGINE" in the Operation section of this
manual). After engine has started, move throttle control
to idle (slow) position.
•
Release parking brake.
•
Slowly move the mo tion control lever for ward and slowly
drive tractor off skid.
•
Apply brake to stop trac tor, set park ing brake and place
motion con trol lever in neutral po si tion.
•
Turn ignition key to "STOP" position.
Continue with the in struc tions that follow.
TO INSTALL BAGGER COM PO NENTS TO
TRAC TOR (See Figs. 4A-4D)
•
Remove discharge chute from rear of tractor. Unhook
the two (2) straps and pull chute out and away from
tractor.
•
Remove the two (2) 3/8 nuts and flat washers from the
bolts at the tractor back plate.
DISCHARGE
CHUTE
3/8 NUT
FLATWASHER
7
FIG. 4A