1. Manuals
  2. Brands
  3. Faroudja Manuals
  4. Computer Hardware
  5. DVP1000
  6. Installation and operation manual

Faroudja DVP1000 Installation And Operation Manual

Digital video processor
Hide thumbs
Table of Contents

Advertisement

Quick Links

DVP1000
Digital Video Processor
Installation and
Operations Manual
NTSC Model
™

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the DVP1000 and is the answer not in the manual?

Questions and answers

Related Manuals for Faroudja DVP1000

Summary of Contents for Faroudja DVP1000

  • Page 1 DVP1000 Digital Video Processor Installation and Operations Manual NTSC Model ™...

  • Page 2: Quick Start

    Area test pattern, align the image size, position and products. blanking first using the controls found in the display device. Only use these controls in the DVP1000 if the display device does not offer these controls or if there CONNECTIONS is not enough range.

  • Page 3: Safety Precautions

    – All warnings on the product and in the operating CAUTION : instructions should be adhered to. Changes or modifications not approved by Faroudja – Unplug this product from the wall outlet before could void the user’s authority to operate the cleaning.
  • Page 4 SAFETY PRECAUTIONS – This product should be operated only with the type e) If the product has been dropped or damaged in of power source indicated on the label. If you are not any way. sure of the type of power supply to your home, f ) When the product exhibits a distinct change in consult your product dealer or local power company.

  • Page 5: Table Of Contents

    No part of this document may be copied, photocopied, translated, or reproduced to any electronic medium or machine readable form without prior consent, in writing, from Faroudja Laboratories, Inc. The Faroudja name, logo and Picture Plus are registered trademarks of Faroudja, Inc. Specifications subject to change without notice. All Rights Reserved.

  • Page 6: Installation

    2. Composite video input (BNC) for sources such be moved or returned for service. Shipping unit back as Laserdisc players, cable TV, VHS tape to Faroudja for service not in the original box may decks, 8mm tape decks. result in voiding warranty.

  • Page 7: Connecting Hdtv Satellite Receivers

    (12V @ 100mA Max. 3.5mm 2 pin with HDCP Encription connector, Tip = +12V, Sleave = Gnd) Note: The DVP1000 pass-through input will “pass ” 11.RS232 D9F connection for use with RS232 the input signal to the output stage in the same control systems.

  • Page 8: Front Panel Control

    When the desired rate is displayed on the reset firmware. See the setup section of the manual for details. LCD display, press the STORE key. The DVP1000 will ask you "Are you sure" and press the STORE key 2. Power/Standby: Press to turn the unit On again.
  • Page 9 LCD Timer 6-255 (40 Default) Note: Each input on the DVP1000 can be activated Note: setting the timer to 5 or lower sets the LCD or deactivated to simplify operation so unused inputs backlight to Always On.

  • Page 10: Processor Ir Remote And On-Screen-Display Operation

    ON SCREEN DISPLAY (OSD) OSD OPERATION Accessing the OSD The DVP1000 is shipped with a Infrared remote • Press Menu button to bring up main Index. control that allows for direct access to most commands used to control the processor.

  • Page 11: Operating The Processor

    Note: Note: The Pass-Thru input cannot be selected permanent image burn-in. Image burn-in is not covered by Faroudja’s warranty from the OSD since an OSD is not available on that input. Use the Input button on the remote to select it.
  • Page 12 DVP1000 in the Factory preset setting. Then use the achieved and then store these custom settings in the DVP1000 controls only if the display runs out of range or Presets. It is important to not use too much Detail as the does not offer these controls.

  • Page 13: Test Pattern List

    DVD is not available, then use the internal test 100IRE Rev. CB: Color bars for decoder check patterns provided in the DVP1000. Note: The test pattern generator in the DVP1000 is set to SMPTE standards. To insure proper output RS232 INSTRUCTIONS...
  • Page 14 RS232 CODES Following the header, a comma is used to delimit the are terminated with a carriage return (0x0d or 13). header from the command. All the commands with Maximum command string length is 250 characters. their descriptions are listed below. All the text strings The header and command are not case sensitive OPERATION COMMANDS (Used for day-to-day operation)
  • Page 15 1024 x 768 1280 x 768 1366 x 768 1440 x 960 1280 X 1024 SR10 DILA SR11 1400 x 1050 SR12 1920 x 1080 Note: Enter DVP, FST in a terminal driver program to get the default numbers or contact Faroudja.

  • Page 16: Help Menus

    HELP MENUS TEST PATTERN HELP MENU TEST PATTERN HELP MENU TEST PATTERN OFF 100% COLOR BARS REVERSE COLOR BARS 10 STEP GREY LUMA RAMP CB RAMP CR RAMP BLACK SCREEN GREEN SCREEN RED SCREEN TP10 BLUE SCREEN TP11 CONVERGENCE TP12 ACTIVE BORDER TP13 SMPTE PATTERN...

  • Page 17: Specifications

    SPECIFICATIONS Inputs (Interlaced) Format NTSC Only Composite(BNC) 1vpp S-Video (4-pin DIN) 1vpp C -286mvpp Component (BNC) Auto-detect: Y -1vpp(SMPTE) 480i/480p sent to upconverter, Cr -700mvpp 1080i or 720p sent to upconverter. Cb -700mvpp RGB ( BNC) Interlaced Comp. Sync -1vpp RGB -700mvpp HD/PC Pass-Thru D15F...

  • Page 18: Warantee

    Faroudja’s option, replace defective products or portions thereof. Warranty may be void if unit is returned to Faroudja Service not shipped in the original shipping carton. THE FOREGOING WARRANTY IS IN LIEU OF ALL WARRANTIES EXPRESSED,...

Table of Contents