TP-Link TL-SF1005D User Manual

RJ45 Ports. All ports can work as the Uplink port, and the
"Uplink" mark under Port 8 can be ignored.
8(UPLINK) 7 6 5 4 3 2 1
Figure 3-2 TL-SF1008D Switch Rear Panel sketch
3.3 LED indicators
The LED indicators include Power LED and Link/Act LEDs. The
LED indicators are used for monitoring and troubleshooting of
the Switch. The following section shows the LED indicators for
the Switch along with an explanation of each indicator.
Figure 3-3 TL-SF1008D Switch LEDs sketch
Ø Power LED: This indicator will light up when the Switch
powers up. If the LED is not lit, please check the power
adapter and connection.
Ø LINK/ACT LEDs: These LEDs indicate Link/Active status.
One LED indicator will light green when a device is
connected to the corresponding port. It flashes when data
is being transmitted or received on the connection.
4
Appendix A: Specifications
General
Standards IEEE802.3 10Base-T, IEEE802.3u 100Base-TX
Topology Star
Protocol CSMA/CD
Data Transfer Ethernet: 10Mbps (Half Duplex), 20Mbps (Full Duplex);
Rate Fast Ethernet: 100Mbps (Half Duplex),
200Mbps (Full Duplex)
Network Media 10BASE-T: UTP category 3, 4, 5 cable (maximum 100m)
(Cable) EIA/TIA-568 100Ù STP (maximum 100m)
100BASE-Tx: UTP category 5, 5e cable (maximum 100m)
EIA/TIA-568 100Ù STP (maximum 100m)
Number of Ports 5/8/16 10/100Mbps Auto-Negotiation ports
LED indicators Power, Link/Act
Transfer Method Store-and-Forward
MAC Address Learning Automatically learning, automatically update
Frame Filter Rate 10Base-T: 14880pps/Port;
100Base-Tx: 148800pps/Port
Frame Forward 10Base-T: 14880pps/Port;
Rate 100Base-Tx: 148800pps/Port
Environmental and Physical
Dimensions 5.5" 3.3" 1.2" (140mm 85mm 30mm)
(W D H) (TL-SF1005D/TL-SF1008D)
11.2" 4.6" 1.1" (285mm 116mm 28mm)
(TL-SF1016D)
Power Supply AC12V~ 0.35A for TL-SF1005D
Output AC9V~ 0.8A for TL-SF1008D/ TL-SF1016D
Operating Temperature 0 ~40 (32 ~104 )
Storage Temperature -40~70 (-40 ~158 )
Operating Humidity 10%~90% non-condensing
Storage humidity 5%~95% non-condensing
5
Appendix B: Troubleshooting
1. The Power LED is not lit
Ø Make sure the AC power Adapter is plugged into an outlet
properly and it's connector is plugged into the power jack
of the switch.
Make sure the power source is ON.
Ø
Ø Make sure you are using the TP-LINK power adapter
supplied with your switch.
2. The Link/Act LED is not lit when a device is connected
to the corresponding port
Ø Make sure that the cable connectors are firmly plugged
into the Switch and the device.
Ø Make sure the connected device is turned on and its
adapter is installed correctly and is working.
Ø The cable must be less than 100 meters (328 feet).
Appendix C: Contact Information
For help with the installation or operation of the TP-LINK TL-
SF1005D/TL-SF1008D/TL-SF1016D Switch, please contact us.
E-mail: support@tp-link.com
Website: http://www.tp-link.com
6
User's Guide
TL-SF1005D
TL-SF1008D
TL-SF1016D
10/100Mbps Fast Ethernet Switch