Summary of Contents for Fujitsu Siemens Computers SCENICVIEW B17-3
Page 1
Monitor English Operating Manual SCENICVIEW B17-3/B19-3/P19-3...
Page 2
Are there… ... any technical problems or other questions which you would like to be clarified? Please contact our help desk (see Warranty Booklet). The latest information on our products, tips, updates, etc., can be found on the internet under: http://www.fujitsu-siemens.com...
Page 4
This manual was produced by Xerox Global Services Published by Fujitsu Siemens Computers GmbH Order No.: A26361-K1143-Z120-1-7619 Edition 3 AG 08/07...
Contents Introduction............................1 Notational conventions ......................... 2 Important notes............................. 2 Safety notes..........................2 Power cable..........................4 Transport ............................4 Cleaning ............................4 CE marking........................... 4 FCC Class B Compliance Statement ................... 5 Declaration of Conformity ......................5 Energy Star Guidelines......................... 6 Disposal and recycling .........................
A graphics card (screen controller) with VGA interface or a digital graphics card with DVI interface is required to control the SCENICVIEW B17-3/B19-3/P19-3 LCD monitor. The monitor processes the data supplied to it by the screen controller. The screen controller or the associated driver software is responsible for setting the modes (resolution and refresh rate).
SCENICVIEW B17-3/B19-3/P19-3 Notational conventions The meanings of the symbols and fonts used in this manual are as follows: Pay particular attention to text marked with this symbol. Failure to observe this warning endangers your life, destroys the device, or may lead to loss of data.
Page 11
If you operate the monitor with the swivel arm or wall bracket, it may not be turned by 180°. ● The SCENICVIEW B17-3/B19-3/P19-3 monitor may only be operated in landscape mode (0°) and portrait mode (90°). The control buttons are located at the bottom of the monitor in landscape mode (0°) and at the left-hand side of the monitor in portrait mode (90°).
SCENICVIEW B17-3/B19-3/P19-3 Power cable To guarantee safe operation, use the cable supplied. Use the following guidelines if it is necessary to replace the original cable set. ● The female/male receptacles of the cord set must meet IEC60320/CEE-22 requirements. ● The cable has to be HAR-certified or VDE-certified. The mark HAR or VDE will appear on the outer sheath.
Fax No.: (408) 746-8299 We, Fujitsu Siemens Computers Inc., hereby declare that the equipment bearing the trade name and model number specified above was tested confirming to the applicable FCC Rules under the most accurate measurement standards possible, and that all the necessary steps have been taken and are in force to assure that production units of the same equipment will continue to comply with the Commissions requirements.
20 million tons of carbon dioxide into the atmosphere - the equivalent of 5 million automobiles. As an Energy Star Partner, Fujitsu Siemens Computers GmbH has determined that this product meets the Energy Star guidelines for energy efficiency.
SCENICVIEW B17-3/B19-3/P19-3 Checking the contents of the consignment The display surface of the LCD monitor is sensitive to pressure and scratches. Always hold the device by the casing! ► Unpack all the individual parts. ► Check the delivery for damage incurred during transportation.
SCENICVIEW B17-3/B19-3/P19-3 Installing an ergonomic video workstation Avoid glare from electric Windows Edge of desk lighting. Permissible reaching Avoid direct and reflected glare. sector Position the keyboard where it is easiest to reach. 0° 65° 30° 60° 30° 65° Example layout of monitor,...
SCENICVIEW B17-3/B19-3/P19-3 Mounting and removing the monitor base The display surface is susceptible to scratching! Therefore, lay the monitor on a soft surface when mounting or removing the monitor base. Folding out monitor base When delivered the lower part of the monitor base is folded up and secured to the monitor by a collar.
Page 18
SCENICVIEW B17-3/B19-3/P19-3 ► Proceed according to the four steps in the illustrations to fold out the monitor base. A26361-K1143-Z120-1-7619, edition 3...
SCENICVIEW B17-3/B19-3/P19-3 Removing monitor base Before you can use a swivel arm or a wall bracket, you must remove the monitor base: The display surface is susceptible to scratching! ► Switch off the monitor and pull the power plug out of the power socket.
SCENICVIEW B17-3/B19-3/P19-3 Connecting the monitor Please take note of the safety information in the "Important notes" chapter. CE conformance and optimum picture quality are guaranteed only if you use the data cables supplied. Do not cover the ventilation openings of the monitor.
SCENICVIEW B17-3/B19-3/P19-3 Connecting cables to the monitor The monitor ports are protected by a cover. ► Remove the cover. Power connector DVI-D connection socket (DIGITAL) D-SUB connection socket (ANALOG) Security slot for "Kensington Lock" AUDIO-IN connector Cover position Holes for fixing swivel arm or wall bracket The data cables supplied have two 15-pin D-SUB connectors / two 24-pin DVI connectors for connection to the monitor and to the computer.
SCENICVIEW B17-3/B19-3/P19-3 Connecting cables to the computer Information on the computer connections and interfaces is contained in the operating manual for your computer. If your computer has two monitor ports ("onboard" screen controller and separate graphics card), the monitor port for the separate graphics card is usually active.
SCENICVIEW B17-3/B19-3/P19-3 Adjusting portrait format The monitor can be turned from the "wide format" (landscape mode) into the "high format" position (portrait mode). ► Grasp the monitor with both hands on the right and left edge of the casing, move it into the highest position and turn it clockwise until it is in the portrait position.
SCENICVIEW B17-3/B19-3/P19-3 Switching the monitor on and off (P19-3) The main switch on the underside and the On/Off switch on the front of the monitor are used to switch it on and off. ► Switch on the monitor via the main switch (4) on the underside.
SCENICVIEW B17-3/B19-3/P19-3 Notes on power management If your computer is equipped with power management, the monitor can support this function fully. Here the monitor does not distinguish between the individual energy-saving modes of the computer (standby mode, suspend mode and OFF mode), as it is capable of immediately switching into the mode with the highest energy-saving effect.
SCENICVIEW B17-3/B19-3/P19-3 Changing the monitor settings When putting the monitor into operation for the first time, the screen display should be optimally adapted to the screen controller used and adjusted in accordance with your needs. Choosing basic monitor settings using the supplied software...
SCENICVIEW B17-3/B19-3/P19-3 Locking the OSD menu The OSD menu can be locked to prevent accidental or unauthorised changes to the monitor settings. ► Press and hold the SELECT/MENU button for a few seconds while you switch on the monitor with the ON/OFF switch.
Page 28
SCENICVIEW B17-3/B19-3/P19-3 The corresponding setting window (here: Image Adjust ) is displayed (on the right-hand side). The first function ( H-Position ) is highlighted. ► If necessary, press the button to mark another function. ► Press the SELECT/MENU button to select the highlighted function.
Page 29
SCENICVIEW B17-3/B19-3/P19-3 Adjusting size and position Calling the Image adjust setting window H-Position Adjusting the horizontal position With this function you move the picture to the left or to the right. V-Position Adjusting the vertical position With this function you move the picture up or down.
Page 30
SCENICVIEW B17-3/B19-3/P19-3 Setting display of the OSD menu Calling the OSD Setup setting window Language Setting language for the OSD menu With this function you choose between English (default setting), French, German, Italian and Spanish as the language for the OSD menu.
SCENICVIEW B17-3/B19-3/P19-3 Displaying information Calling the Information setting window With this function the model designation, serial number, resolution, H/V frequency, input signal and polarity of the synchronisation signal are displayed. Notes on ergonomic colour adjustment If you select colours for the display in your application programmes, take note of the information below.
SCENICVIEW B17-3/B19-3/P19-3 Troubleshooting Should an error occur, first check the following points. If the distortion is still not eliminated, the monitor should, if possible, be checked on another computer. If you are unable to solve the problem, please inform our help desk.
Page 33
SCENICVIEW B17-3/B19-3/P19-3 Having this problem? Check the following points: Picture is wrongly adjusted ► Press the SELECT/MENU button to activate the function Factory Recall . The Auto Processing message is displayed. Picture disturbances (vertical lines) ► Press the EXIT/AUTO button to perform the auto- adjustment of the screen.
SCENICVIEW B17-3/B19-3/P19-3 Notes regarding the DIN EN ISO 13406-2 standard Permanently unlit or lit pixels The standard of production techniques today cannot guarantee an absolutely fault-free screen display. A few isolated constant lit or unlit pixels (picture elements) may be present. The maximum permitted number of pixels faults is stipulated in the stringent international standard ISO 13406-2 (Class II).
SCENICVIEW B17-3/B19-3/P19-3 Technical data B17-3 B19-3 / P19-3 Dimensions and weight Visible diagonals: 43 cm 48 cm Dot pitch: 0.264 mm 0.294 mm Screen size: Width: 337.9 mm 376.3 mm Height: 270.3 mm 301 mm Maximal resolution: 1280 x 1024 1280 x 1024 Dimensions incl.
VGA interface, it can automatically read the data for ensuring optimum operation from your monitor and select the appropriate settings. If the monitor SCENICVIEW B17-3/B19-3/P19-3 is not yet displayed in the list of monitors, you can select the following monitor instead:...
SCENICVIEW B17-3/B19-3/P19-3 Pin assignment D-SUB Meaning Meaning Video input red +5 V (DDC) Video input green Sync. earth Video input blue Earth Earth DDC-Data Earth H. sync Red video earth V. sync Green video earth DDC Clock Blue video earth...