Advertisement
10. nAIl/stAple gun mAIntenAnce
WARnIng! disconnect the nail/staple gun from the air supply before refilling with nails/staples, servicing or performing any maintenance.
replace or repair damanged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
10.1.
If an air system oiler is not available, lubricate the air nail/staple gun daily with a few drops of air tool oil, dripped into the air inlet
before use.
to re-order air tool oil, use sealey part nos. ato500s (500ml) or ato1000s (1 litre).
10.2.
clean the nail/staple gun after use.
10.3.
loss of power or erratic action may be due to the following:
a) excessive drain on the air line. moisture or restriction in the air pipe. Incorrect size or type of hose connectors. to remedy, check the
air supply and follow the instructions in section 8.
b) Grit or gum deposits in the nail/staple gun may also reduce performance. flush the nail/staple gun out with gum solvent oil or an
equal mixture of sae no 10 oil and kerosene. allow to dry before use. If continuing to experience problems, contact your local
sealey service agent.
10.4. check moving parts alignment, trigger, safety mechanism and spring on a regular basis.
10.5.
on a weekly basis, check the security of the hex bolts holding the driver guide plate in place and tighten if necessary (fig.6).
10.6.
for a full service, contact your local sealey service agent.
10.7.
When not in use, disconnect from air supply, clean nail/staple gun and store in a safe, dry, childproof location.
11. nAIl/stAple gun tRouBleshootIng
FAult
1) air leak near top of tool or in trigger area.
2) air leak near bottom of tool.
3) air leak between body and cylinder cap.
4) Blade driving fastener too deep.
5) Gun operates sluggishly, cannot drive fastener.
6) tool jams.
7) tool skips fasteners.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
ImpoRtAnt: no liability is accepted for incorrect use of this product.
WARRAntY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
InFoRmAtIon: for a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
o-ring in trigger valve damaged.
trigger valve head is damaged.
trigger valve stem or seal damaged.
Worn or damaged o-rings or bumper.
Worn or damaged o-rings or seals.
Worn or damaged bumper.
Inadequate air supply / lubrication.
Worn or damaged o-rings or seals.
exhaust port in cylinder head blocked.
Incorrect or damaged fasteners.
damaged or worn driver guide.
magazine or nose screw loose.
Worn bumper or damaged spring.
dirt or damaged fasteners in magazine.
Worn or dry o-ring on piston.
cylinder cover seal leaking.
recycle unwanted materials instead of disposing of them as waste. all tools, accessories and
packaging should be sorted, taken to a recycle centre and disposed of in a manner
which is compatible with the environment.
When the product is no longer required, it must be disposed of in an
environmentally protective way.
sole uk Distributor, sealey group,
Kempson Way, suffolk Business Park,
Bury st. edmunds, suffolk,
IP32 7ar
Original Language Version
cAuse
loose screws.
loose screws.
air pressure is too high.
magazine is dirty.
dirt in front plate.
environmental protection.
RemeDY
check and replace.
tighten screws.
check and replace o-rings or bumper.
tighten screws.
check and replace o-rings or seal.
check / replace bumper.
adjust air pressure.
check air supply/ drop oil into air inlet.
check and replace o-rings or seals.
replace damaged internal parts.
. use correct/undamaged fasteners.
check / replace driver guide.
tighten magazine / screw.
clean magazine.
replace bumper or pusher spring.
clean drive channel on front plate.
check / clean magazine.
replace / lubricate o-ring.
replace sealing washer.
www.sealey.co.uk
01284 757500
Web
sales@sealey.co.uk
01284 703534
email
sa0615KIt
Issue: 1- 08/04/10
Advertisement
