Advertisement
6. compRessoR tRouBleshootIng
FAult
1a) Pressure drop in the tank.
1B) Pressure drop in the tank.
1c) Pressure drop in the tank.
2)
Pressure switch valve leaks when
compressor is idle.
3)
air leaks from tank body or tank welds.
4a) motor stops and will not restart.
4B) motor stops and will not restart.
5)
compressor stops and does not restart.
6a) compressor does not stop at max. pressure.
6B) compressor does not stop at max. pressure.
6c) compressor does not stop at max. pressure.
7)
compressor noisy with metallic knock.
8)
excessive moisture in discharged air.
7. nAIl/stAple gun sAFetY
READ THE SAFETY INSTRUCTIONS IN SECTION 1 FIRST, THE FOLLOWING SAFETY INSTRUCTIONS ADDITIONALLY APPLY
TO THE NAIL/STAPLE GUN
WARnIng! disconnect from air supply before refilling with nails/staples, servicing or performing maintenance.
maintain the nail/staple gun in good condition (use an authorised service agent).
replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
use in suitable clean and tidy work area, free from unrelated materials. ensure there is adequate lighting.
WARnIng! always wear approved eye and/or face and hand protection when operating the nail/staple gun.
maintain correct balance and footing. ensure the floor is not slippery and wear non-slip shoes.
ensure workpiece is secure before operating the nail/staple gun. never hold a workpiece by hand.
Prolonged exposure to vibration from this nail/staple gun may pose a health risk. It is the owner's responsibility to correctly assess the
potential hazard and issue guidelines for safe periods of use and offer suitable protective equipment.
Do not use any other power source other than an air compressor.
Do not operate the nail/staple gun near any flammable substance or on any container that once contained an flammable substance.
Do not operate the nail/staple gun if any parts are damaged or missing as this may cause failure and/or personal injury.
Do not carry the nail/staple gun by the hose, or yank the hose from the air supply.
Do not place the nail/staple gun close to your face and do not point at other persons or animals.
Do not carry the nail/staple gun with your finger on the trigger.
Keep hands and body clear of working parts.
If the nail/staple gun is put down during pauses in operation, ensure that it is not placed in a restricted position that could put pressure
on the trigger catch slide, or that the trigger catch slide is not depressed by the weight of the nail/staple gun.
during any extended breaks in operation, disconnect the nail/staple gun from the air supply.
8. nAIl/stAple gun pRepARAtIon
8.1.
Air supply
8.1.1.
Before connecting to an air supply ensure that the trigger release slide is not depressed (fig.6).
8.1.2.
the nail/staple gun requires an operating air pressure of between 70-110psi.
8.1.3.
WARnIng! ensure the air supply is clean and air pressure is maintained and does not exceed 120psi while operating the nail/staple
gun. too high an air pressure and unclean air will shorten the product life due to excessive wear, and may be dangerous causing
damage and/or personal injury.
drain the air tank daily. Water in the air line will damage the nail/staple gun and will invalidate your warranty.
8.1.4.
8.1.5.
clean the air inlet filter weekly. recommended hook-up is shown in fig.7.
cAuse
air leaks at connections.
air leaks from safety valve.
air leaks from cylinder head gasket.
non-return valve seal defective.
Internal corrosion caused by infrequent tank
draining or non permitted modifications to tank.
thermal cut out has operated.
Plug fuse has burnt out.
motor failure.
Pressure switch fault..
filter clogged
head gasket or valve fault.
Bearing or piston damage.
high humidity environment.
Original Language Version
RemeDY
run compressor to max. pressure, switch off.
Brush soap solution over connections and look for
bubbles. tighten connections showing leaks.
If problem persists contact authorised service agent.
operate the safety valve manually. If valve
continues to leak when in the closed position it
should be replaced.
check tightness of head bolts. If leak continues
contact authorised service agent.
empty the air tank, remove the non-return valve
cap and clean, or if necessary, replace the seal.
tank could rupture or explode. cannot be repaired.
DIscontInue use ImmeDIAtelY.
allow to cool for 10 to 15 minutes before restarting.
replace fuse and restart unit. If repeat
occurs, contact authorised service agent.
contact authorised service agent..
contact authorised service agent.
clean or replace filter element.
contact authorised service agent.
contact authorised service agent.
drain tank after each use.
sa0615KIt
Issue: 1- 08/04/10
Advertisement
