Advertisement
BLISSTOOL
Contents
Introduction................................................
Features......................................................
Assembling your Blisstool......................
Controls.......................................................
Getting Started..........................................
Pointers.......................................................
Battery Charging.......................................
Warranty.....................................................
RHOS and WEEE compliant.....................
LTC64X v3
User Guide
Version: USA/CP
2007 - 2012 © BLISSTOOL
2
3
4
5
7
9
11
12
13
Advertisement
Table of Contents
Related Manuals for Blisstool LTC64X v3
Summary of Contents for Blisstool LTC64X v3
-
Page 1: Table Of Contents
BLISSTOOL LTC64X v3 User Guide Version: USA/CP 2007 - 2012 © BLISSTOOL Contents Introduction………………………………………… Features…….……………………………………….. Assembling your Blisstool…...……………. Controls………………………………………………. Getting Started…………………………………… Pointers………………………………………………. Battery Charging………………………………… Warranty…………………………………………….. RHOS and WEEE compliant…………………... -
Page 2: Introduction
Introduction The BLISSTOOL LTC64X v3 is an induction balance metal detector that has the ability to go DEEP in even the harshest of soil conditions. Unlike other VLF machines, the gain does not need to be at high levels to penetrate great depths. -
Page 3: Features
Features – Operating frequency 8.0 kHz Induction Balance – Adjustable operating frequency (+/-60Hz) – Operating mode: motion – Audio discrimination – Able to handle the harshest terrain and operate where other VLF machines have difficulty – Standard 28cm (11") DD search coil –... -
Page 4: Assembling Your Blisstool
Assembling your BLISSTOOL metal detector 1. The search coil is connected to the lower connecting rod utilizing the supplied spacers, plastic bolt and plastic nut. 2. The upper part of the lower connecting rod is attached to the lower part of the intermediate connecting rod via the small fixing ring, and adjusted to the appropriate length. -
Page 5: Controls
Description of Controls The VOLUME on/off control turns on your detector and adjusts the volume level. WARNING: the volume output is very loud so be sure to start off testing your headphones without having them on your ears! Headphones are different with some having volume controls and some not - so be cautious when learning where to set your volume level. - Page 6 TONE control allows you to hear target responses at a level that is preferred by you. If you run your BLISSTOOL with an audible threshold, the tone control can also be used to find the most stable tone.
-
Page 7: Getting Started
5. With your coil at waist level, lower the coil in a pumping motion, to about 2” above the ground and listen for a loud response. Adjust the AUTO ZONES toggle trying all three zones to see which one is the quietest. A slight “click” sound is OK but if your BLISSTOOL still beeps... - Page 8 6. Now that you are ground balanced at the proper gain level for your BLISSTOOL to run smoothly, raise your DISCR LEVEL to “5” and your DISCR DEPTH according to where you set your gain. See below.
-
Page 9: Pointers
General Pointers The BLISSTOOL is a true Beep-n-Dig machine. There is no meter, no tone ID and no unnecessary “bells and whistles”. Perfect balancing with no filters = extreme depth! When the machine is set correctly, good targets sound loud and clear while iron will crackle and break up. - Page 10 6” above the ground. Bury a coin and practice this technique for probable depth. Less is more with your BLISSTOOL when it comes to GAIN and DISCR DEPTH. Don’t be concerned if your BLISSTOOL only operates well at a GAIN of “1”.
-
Page 11: Battery Charging
Battery Your BLISSTOOL LTC64X v3 is equipped with a high quality, low weight and long life LiPo battery 11.1V, 2200mAh The LiPo battery has about 800 cycles of charge-discharge (battery life), after which time it must be replaced with a new battery. -
Page 12: Warranty
Warranty Support and Service The BLISSTOOL LTC64X v3 metal detector has a 3 year worldwide transferable warranty covering the components and any factory flaws. If the electronic block (control “box”) is tampered with or the integrity of the seals placed on the lid of the electronic block is opened, the warranty is not valid. -
Page 13: Rhos And Weee Compliant
In order to be RoHS compliant, the BLISSTOOL LTC64X uses high quality electronic components, unleaded tin for soldering and pcb board with a final coating of nickel-gold.
Need help?
Do you have a question about the LTC64X v3 and is the answer not in the manual?
Questions and answers