Initial Installation - Nikai NDVD1073VR Instruction Manual

Initial Installation

Switch the TV on.
You can also start "AUTO SEARCH" in the SETUP "PR PRESET"
To tune in new stations (manual tuning) and to enter station names see page 27-28.
Setting up the player
CHECK IT!
• If you don't see the menu picture below after you press the menu button it may be because you
don't use a RCA cable and you need to tune the television to the player (see 'Connecting your
player through RF lead' on page 12). Normally a new player outputs a signal via the RF lead on
transmission channel 52. Search for the menu picture with the channel tuning function of your TV
set (see its user manual). Some televisions allow you to key in the transmission channel number in
their tuning set-up menu.
• In case there will be interference problems with other transmission channels when the player
outputs a signal on transmission channel 52, the AUTO SEARCH process usually recommends an
alternative, as in step 4.
• There is a another way of setting RF output channel, if needed please see 'Connections and
Assembling on page 35'. It does not apply to models which do not generate the RF output signal.
1
Press on the remote control and RF52 will be displayed on
the front of your player.
Select a free channel on your TV and manual tune the channel
until the blue screen as shown in step 2 appears. Refer to the TV
manual for more details.
You should see this picture the first time you switch on the TV
2
and player.
Select the wanted language with PR+ or PR- button. Press OK to
confirm.
OK for "AUTO SEARCH!".
3
"AUTO SEARCH" tunes in all the stations you can receive in your
country.
If the clock has not been set, the clock setting screen will appear.
4
Please see "Setting time and date" on page 20.
18
"AUTO SEARCH".
LANGUAGE SET
ENGLISH
PYCCKNZ
ÔESKY
MAGYAR
PR+/-:SELECT
OK:CONFIRM SETUP:END
CH 25
PLEASE WAIT...
SETUP:END
CLOCK SET
TIME - - : - -
DATE - - / - - /- - - -
0-9:SETUP (HOUR)
/ :CORRECT SETUP:END
If other stations are positioned on near the current RF OUTPUT
5
CH, the guide message appears automatically.
The player recommends the optimal RF OUTPUT CH number
automatically.
Press the [OK] button to confirm the recommended RF channel.
6
Should you wish the stations to have the same numbers as those
used on the TV, follow the instructions in "Sorting programme
locations" on page 29.
Else ...
exit the basic installation function and enjoy your player.
• If the signal from the player is coming into the TV through
the RF lead, the picture will disappear when you press OK
at step 7. You will need to re-tune your television to the new
UHF transmission channel.
Should you wish the stations to have the same numbers as those
7
used on the TV, follow the instructions in "Sorting programme
locations" on page 29.
Else ...
Press the SETUP button to exit the set-up menu and enjoy your
player
Up [PR+], down [PR-], OK and 'confirm'
• Notice the on-screen prompts which the video recorder generates to tell you which button to press. In general
the up and down 'navigation' buttons select or highlight something and the OK button confirms it .
• [PR+] and [PR-] are the same buttons as 'up' and 'down'.
• In the DVD section it is usually the left and right buttons which 'select'.
RF OUTPUT SET
CURRENT CH 52
RECOMMENDED CH 54
0-9:SELECT(21-69)
OK:CONFIRM SETUP:END
IMPORTANT!
PLEASE CHANGE THE TV
CH TO 54.
MANUAL SET
PR01 P-01 PR08 P-08
PR02 P-02 PR09 P-09
PR03 P-03 PR10 P-10
PR04 P-04 PR11 P-11
PR05 P-05 PR12 ----
PR06 P-06 PR13 ----
PR07 P-07 PR14 ----
PR+/-:SELECT
OK:CONFIRM SETUP:END
19