Subscribe to Our Youtube Channel
Related Manuals for Future Design FDC-9090
Summary of Contents for Future Design FDC-9090
- Page 1 9090 User's Manual 9090 User's Manual FDC-9090 FDC-9090 Self-Tune Fuzzy / PID Self-Tune Fuzzy / PID Process / Temperature Controller Process / Temperature Controller...
- Page 2 Copyright a August 2001, Future Design Controls, all rights reserved. No part of this publication may be reproduced, transmitted, transcribed or stored in a retrieval system, or translated into any language in any form by any means without the written permission of Future Design Controls.
- Page 3 1. INTRODUCTION 1. INTRODUCTION This manual contains information for the installation and operation Up Key of the Future Design Control’s model FDC-9090 Fuzzy Logic 4. INPUT RANGE & ACCURACY 4. INPUT RANGE & ACCURACY micro-processor based controller. The Fuzzy Logic is an essential feature of this versatile...
- Page 4 6.2 WIRING DIAGRAM 6.2 WIRING DIAGRAM 'fine-tune' the control settings. FDC-9090 It is important that prior to making changes to the control settings that you record the current settings for future reference. Make slight changes Alarm to only one setting at a time and observe the results on the process.
- Page 5 7.5 MANUAL TUNING PROCEDURE Step 1: Adjust the integral and derivative values to 0. This inhibits the The FDC-9090 controller can be configured to act as either a fixed rate and reset action set point controller or as a single ramp controller on power up. This...
- Page 6 7.6 Flow Chart 7.6 Flow Chart 7.7 PARAMETER DESCRIPTION 7.7 PARAMETER DESCRIPTION PROCESS VALUE DISPLAY Level 0 SET POINT VALUE DISPLAY INDEX DESCRIPTION **DEFAULT CODE ADJUSTMENT RANGE SETTING Long (6 seconds) Set point Value Control Undefined *Low Limit to High Limit Value Alarm Set point Value * Low Limit to High Limit Value.(if =0, 1, 4 or 5)
- Page 7 PROCESS VALUE DISPLAY Supplemental Instruction for the New Version V7.3 ONLY Level 0 SET POINT VALUE DISPLAY Long NOTE: This procedure does NOT have to be performed unless the (6 seconds) LLit and/or Hlit have been changed from the factory setting. This routine properly adjusts the calibration values IF the Llit and/or Hlit parameters have been changed from factory default.
- Page 8 Connect the Millivolt source as shown below: Positive lead to terminal 5 and negative lead to terminal 4. Set the Millivolt source for 0.00 MV. Millivolt wiring Diagram Millivolt wiring Diagram FDC-9090 AC power to unit AC power to unit under calibration under calibration...
- Page 9 RTD calibration.* Connect a 3 wire RTD simulator to the RTD input as shown below: The “hot” lead connects to terminal 3. The 2 common leads go to terminals 4 & 5. FDC-9090 AC power to unit AC power to unit 6.2 WIRING DIAGRAM...
- Page 10 This Page Intentionally Left Blank...
- Page 11 Future Design Controls Facilities and to conform at that time to the specifications set forth in the relevant Future Design Controls manual, sheet or sheets for a period of 3 forth in the relevant Future Design Controls manual, sheet or sheets for a period of 3 years after delivery to the first purchaser for use.
- Page 12 Future Design Controls Future Design Controls 7524 West 98th Place, P .O. Box 1196 7524 West 98th Place, P .O. Box 1196 Bridgeview, IL. 60455 USA Bridgeview, IL. 60455 USA 888.751.5444 - Office 888.751.5444 - Office 888.307.8014 - Fax 888.307.8014 - Fax 866.342.5332 - Technical Support...
Need help?
Do you have a question about the FDC-9090 and is the answer not in the manual?
Questions and answers