Page 2
Copyright Notice This document and product is copyrighted, May 2001, by ICP Electronics Inc. All rights are reserved. No part of this manual may be reproduced, copied, or translated without prior notice to ICP Electronics Inc. The information provided in this document is for reference only. We do not assume any responsibility arising out of the application of the products.
1.2 Product Specifications 1.3 Dimensions Chapter 2 System Setup 2.1 Filter of the Lockable Door 2.2 The Front Panel of EC-1040 2.3 Removing the chassis cover 2.4 Disk Drives Installation 2.5 Fan Installation 2.6 Power Supply Installation 2.7 The Card Clamp & Backplane Installation...
Chapter 1 Product Information 1.1 General Information EC-1040 is a PC/AT compatible computer designed for industrial applications. It is a steel rugged chassis specially designed to work under harsh environment for high reliability application. The EC-1040 features 14-slots passive backplanes and high reliability AC/DC input power supply (options available are: ACE-920A, ACE-932A, ACE932T, ACE925T, ACE925C, ACE-916V, ACE-935A, ACE-832A, ACE-R30A…...
Three 5.25” drive and one 3.5” open FDD or HDD space. Programmable Message and Alarm Function EC-1040 provides customer a programmable display for server name, IP address, system time, alarm message,… etc. We can use the utility tool to program message by RS-232 port.
1.3 Dimensions TEMP LED LAN LED FAN LED BUZZER OFF...
Page 7
Chapter 2 Installation Procedure The following procedures are provided to assist you in installing the EC-1040, please follow the steps below: 2.1 Drive of the Lockable Door A lockable door installed in the front panel .The Drive is located at the inner of the door.
2.2 The Front Panel of EC-1040 The drive bays, fans and power switch are in the front panel. Drive bays and power switch are protected by lockable door for unauthorized misuse and particle environment. SYSTEM RESET POWER ON/OFF SWITCH...
2.3 Removing the chassis cover The top cover is fixed by 6 screws at each side and the top of the chassis, remove them and slide the cover to the rear of the chassis. Figure below shows how to remove the chassis cover.
2.4 Disk Drives installation 1. Open the lockable door in the front panel 2. Remove 2 screws that lock the disk drive bay 3. Pull out the disk drive bay 4. Attach the drivers to the bracket with screws and connect flat cable & power cable to the driver 5.
2.5 Fan Installation The EC-1040 is easy to install the fan module in the chassis. It's not need any screw. Plug in the plastic locker; connect the fan cable with the A 106 controller board.
2.6 Power Supply Installation 2.6.1 General Power Supply For the EC-1040 installation: ACE-920A/ 932A/ 932T/ 935A /925T/ 925C/ 916V/ 32A… SCREW X 2 SCREW X 3...
Page 17
2.6.2 Redundant Power Supply for the EC-1040 installation: ACE-R30A SCREW X 2...
2.7 The Card Clamp & Backplane Installation Figure below illustrates how to install the backplanes on the Rack-3000. To install the backplanes in the chassis, remove the clamp panel first, then put the backplanes inside the chassis and screw it. Use 2 screws(6#32*6) to fix the card clamp...
Cable Management EXT. VGA Cable M TO F 32000-022301 EXT. VGA Cable M TO M 32000-023200 CPU CARD Âà´«½u M TO M TO PC DM-64T LCD MODULE 32000-017300 WIRE CABLE 32100-035600 5V S/B JP12 4P DC POWER CABLE POWER SUPPLY 32100-042500 JP12 A106...
Page 24
APPENDIX B POWER SUPPLY RACK-3000 was designed for PS/2 size power supply. ACE-R30A PS/2 POWER SUPPLY SERIAL...
Page 25
Model Name ACE-920A ACE-932T ACE-932A ACE-935A ACE-832A Description 250W PS/2 size AC 300W -48V PS/2 300W PS/2 size AC 350W PS/2 size AC 300W PS/2 size ATX input power supply size DC input power input power supply input power supply power supply (PFC) supply...
Page 26
APPENDIX C Drive Bay 5.25" Drive Bay 3 open space 3.5" Drive Bay 2 open 1 Internal space...