Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for ICP Electronics MPC-52P
Summary of Contents for ICP Electronics MPC-52P
- Page 1 MPC-52P 12.1" LCD 6-slot Chassis...
- Page 2 Copyright Notice This document and product is copyrighted, April 1999, by ICP Electronics Inc. All rights are reserved. No part of this manual may be reproduced, copied, or translated without prior notice to ICP Electronics Inc. The information provided in this document is for reference only. We do not assume any responsibility arising out of the application of the products.
-
Page 3: Table Of Contents
Table of Contents Chapter 1 Product Information 1.1 General Information 1.2 Product Specifications 1.3 Mechanical Dimensions 1.4 CD-ROM, 3.5" FDD and HDD 1.5 Brightness adjustment and Power switch Chapter 2 System Setup 2.1 Adding cards 2.2 Disk Drives Installation 2.3 Power Supply Installation 2.4 The Fan Installation 2.5 Panel Mounting Chapter 3 Maintenance... -
Page 4: Chapter 1 Product Information
MPC-52P can be equipped with BP-6S or IP-6S 6-slot backplane. Plug-in Card Size Max. card Size:275mm Power Supply The standard industrial power supply of MPC-52P is equipped with ACE-890A. The optional power supplies are: ACE-890T -48VDC Input power supply ACE-890P +100VDC Input power supply... -
Page 5: Product Specifications
1.2 Product Specifications Front Panel: meets NEMA 4. Disk Drive Bay: Support one 5.25" CD-ROM , one 3.5" FDD and one 3.5" HDD LCD interface: 44-pin connector to JUKI series CPU board or PLC-655/PLC-508 LCD control card. Cooling Fan: one 80mm fan with filter and one 60 mm fan for power supply. Lockable drive door design. - Page 6 1.3 Dimensions The following diagram indicates the dimensions of MPC-52P. Front panel: 344(W)x260(H)x8(D)mm Cabinet: 332(W)x248(H)x225(D) mm U N I T : m m - 4 -...
-
Page 7: Cd-Rom, 3.5" Fdd And Hdd
1.4 CD-ROM, 3.5" FDD and 3.5" HDD MPC-52P is equipped with one CD-ROM and 3.5" FDD in the side panel that can be accessible by opening the lockable drive door as the following diagram shown. As for 3.5" HDD, it can be installed by opening upper cover. -
Page 8: Brightness Adjustment And Power Switch
1.5 Brightness adjustment and power supply switch The brightness adjustment, contrast adjustment, AC input and power switch are placed at the rear of chassis as the following diagram shown. FAN FILTER BRIGHTNESS adj. CONTRASTNESS adj. (8cm ) POWER switch (6cm ) AC INPUT - 6 -... -
Page 9: Chapter 2 System Setup
Chapter 2 System Setup The MPC-52P, 12.1" LCD 6-slot Chassis, is very easy to set up for operation. All you have to do is to open the upper cover, install backplane, your CPU card, display control card, hard disk drive and other I/O cards required by your application. -
Page 10: Disk Drives Installation
2.2 Disk Drives installation MPC-52P provides one 5.25" Drive CD-ROM, one 3.5" FDD and one 3.5" HDD. The diagram 1 shows how to install one 5.25" Drive CD-ROM and one 3.5" FDD. As for 3.5" HDD, user need remove the upper panel by releasing the screws as the diagram 2 below shown. -
Page 11: Power Supply Installation
2.3 Power Supply Installation This Panel PC is equipped with ACE-890A power supply, which is fastened by 4 screws as the diagram below shown. Model Input Voltage Rated Load Max Output +5V +12V -12V +5V +12V -12V ACE-890A 85V to 264VAC 2.5A 0.5A 12A - 9 -... - Page 12 2.4 Cooling Fan Installation MPC-52P is equipped with one 80mm cooling fan for system and one 60mm for power supply. The following diagrams indicate the location of fans. - 10 -...
-
Page 13: Panel Mounting
2.5 Panel Mounting MPC-52P can be mounted within a panel as the diagram below shown. Please make sure the dimensions of the case within panel aperture so that your screw holes line up with the mounting bolts on the flange of MPC-52P. -
Page 14: Chapter 3 Maintenance
3.2 Cooling Fan MPC-52P is equipped with 8 cm with removable fan filter and 6 cm cooling fan by the side of chassis. Please refer to the diagram of section 2.4. You have to open the chassis and unfasten the four bolt kits to take fan out for maintenance. The filter is suggested being replaced or cleaned at suitable time, which depends on the working environment. - Page 15 Appendix A Exploded Diagram - 13 -...
- Page 16 Appendix B Display Interface To CPU Display Card <Display Signal> To LCD Panel Backlight To LCD Panel Backlight LCD-05 To LCD Display ITEM PART NO. SPECIFICATIONS Q’ TY REMARK 0169-LCD05-000 LCD-05 8202-1011401 DS14-30S-1.25C/20cm 8202-1008101 VR/10K 8202-1009001 4P FOR BKI 16130/28cm 1 8201-1005601 44P 2.0 M to M/70cm B52-16130-01...
- Page 17 LD-05 Jumpers and Connectors document CN1:LCD CONNECTOR to LCD control card PIN NO Function PIN NO Function +12V +12V +5V(VCC) +5V(VCC) FPVEE SHFCLK ENABKL +5V(VCC) +5V(VCC) CN2:Backlight Inverter Connector ON/OFF Vin is +12V power CN3:Touch Panel Power +12V +5V(VCC) CN4:Backlight Inverter ON/OFF Switch +12V 1-2 On : Operated Inverter 1-2 Off : Inoperated Inverter...
- Page 18 CN5: Flat Panel Display Output Connector to LCD panel DF14-30P-1.25H SHFCLK +5V(VCC) +5V(VCC) CN6: Brightness Adjust Series a Resistor to +5V(VCC) Pin2-3 connects to a 10K Ohm Dimmer Pin1 is reserved for the ponteniometer JP1: Backlight Inverter on/off control 1-2=USE FPVEE 2-3=USE ENBKL - 16 -...
- Page 19 Appendix C Touch Panel Controller +12V RS232 9584A To Touch Panel - 17 -...