Page 1
XP-R210 SERVICE MANUAL COMPACT DISC PLAYER BASIC CD MECHANISM: DA23L • This Service Manual is the “Revision Publishing” and replaces “Simple Manual” of XP-R210<AHA>, (S/M Code No. 09-005-426-3T4). S/M Code No. 09-006-426-3R3...
SPECIFICATIONS Tracking system 3-beam laser Maximum outside dimensions Laser pickup Semiconductor laser 128 (W) x 31.2 (H) x D/A conversion 4-times oversampling digital 129.5 (D) mm (excluding filter + 1-bit DAC projecting parts and controls) Frequency Response 20 – 20,000 Hz (47 K ohms) in.) Output PHONES/LINE OUT jack...
PROTECTION OF EYES FROM LASER BEAM DURING SERVICING This set employs laser. Therefore, be sure to follow carefully the CAUTION instructions below when servicing. Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous WARNING! radiation exposure.
ELECTRICAL MAIN PARTS LIST REF. NO. PART NO. KANRI DESCRIPTION REF. NO. PART NO. KANRI DESCRIPTION C212 87-012-188-080 C-CAP,U 47P-50 CH C213 87-A10-047-080 C-CAP,U 1-10 Z F 87-A21-082-040 C-IC,BA6655AFV C214 87-010-831-080 C-CAP,U,0.1-16F 8A-HC1-605-010 C-IC,MN101C439-AB1 C215 87-A11-063-080 C-CAP,S 4.7-10 Z F 87-A21-446-010 C-IC,MN662782RPT1 C216...
Page 5
REF. NO. PART NO. KANRI DESCRIPTION REF. NO. PART NO. KANRI DESCRIPTION C709 87-A10-047-080 C-CAP,U 1-10 Z F C827 87-A11-061-080 C-CAP,S 2.2-10 K B C710 87-016-421-080 C-CAP,E 10-16 5.5N C828 87-012-286-080 CAP, U 0.01-25 C711 87-016-429-080 C-CAP,E 100-4 5.5N C829 87-012-274-080 CHIP CAP,U 1000P-50B C712...
Page 17
IC DISCRIPTION IC,MN101C439-AB1 Pin No. Pin Name Description 1 ~ 4 Not connected. 5 ~ 7 VLC3 ~ 1 LCD Voltage divider resistor3 ~ 1 (Not used.) Micro-computer power voltage (2.8 V). OSC2 Main clock oscillator (4.2336 MHz). OSC1 Main clock oscillator (4.2336 MHz). Micro-computer GND.
Page 18
Pin No. Pin Name Description MUTE Audio mute output. STANDBY Not used. LCDRDO Wired LCD remote control output. P-OFF Not used. DSCHRG Electric discharge output. CHRG Electric charge output. DISP-DATA LCD display data output. DISP-CLK LCD display data clock output. DISP-CS LCD display data chip selection output.
Page 19
IC,uPD789405AGK-A12-9EU Pin No. Pin Name Description +3 V power supply. BIAS LCD driver power supply. 3 ~ 5 VLC0 ~ 2 LCD driver power voltage. VSS1 GND. 7 ~ 10 COM0 ~ 3 LCD common output. 11 ~ 27 SEG0 ~ 16 LCD segment output.
Page 20
Pin No. Pin Name Description AM-SFT For “DD convertor” oscillator terminal clock shift. DD-SFT For “DD convertor” oscillator terminal clock shift. CLK-SFT “H” output when microcomputer oscillator terminal clock shift. RESET Reset input. XTAL2 Connection terminal to oscillator terminal. XTAL1 Connection terminal to oscillator terminal.
Page 21
IC,MN662728RPT1 Pin No. Pin Name Description DVDD DRAM interface power (terminal No. 2 to 19). 2 ~ 3 D0 ~ 1 DRAM data input/output signal 0 ~ 1. DRAM write enable signal. NRAS DRAM RAS control signal. 6 ~ 7 D2 ~ 3 DRAM data input/output signal 2 ~ 3.
Page 22
Pin No. Pin Name Description AVSS1 Analogue circuit GND. OUTR Rch audio output. AVDD1 Analogue circuit power. FSEL Noise filter ON/OFF switch input. “L” = ON, “H” = OFF. TMOD1 Terminal mode switch input terminal 1, Normally set to “L”. TMOD2 Terminal mode switch input terminal 2, Normally set to “L”.
CD TEST MODE S101 Q204 OPEN/CLOSE SW LAND MAIN C.B TC208 MAIN C.B CN501 TP2(RF) TEST LAND (VC) (TEO) PHONES/LINE OUT IC301 PHONES/LINE OUT (FEO) CN601 IC401 (another side) VR701 LID C.B The servo circuit of this model is designed to be adjustment-free and the adjustment value and disc distinction (CA-DA. CD-R and CD-RW etc.) is adjusted by within the IC.
Page 24
The LCD will change as follows. 6. Confirmation of each servo Example: Test disc: TCD-782, DISC type select: CD-d, Judgement value: 7F, Measurement value: 3D BE. It is possible to confirm the adjustment value of each servo by repeatedly pressing the MODE button while the test disc is playing. The switchover sequence is as stated below.