Usb & Sd-Card Operation - Ricatech RR2000 User Manual

Volume control
Press VOLUME UP / / VOLUME DOWN / on the remote control to adjust the volume.
MUTE
You can temporarily switch off the sound without switching off the unit.
1. Press MUTE / on the remote control to switch off the sound, playback continues without sound.
2. To switch on the sound , you can:
- press MUTE / again;
- adjust the volume controls;
- change source
EQ
Press EQ / on the remote control to select desired EQ mode.
5 modes preset EQ:
RADIO
AM/FM Tuning
1. Press the FUNCTION / to set the unit to TUNER mode.
2. Press STOP/BAND / repeatedly to select your desired waveband. FM or AM
3. Auto Tuning – Press and hold FF / or FB /
station with sufficient reception. If a station in received in stereo, (ST) is shown. Repeat step 3 if necessary until you
find the desired station.
4. Manual Tuning – Press FF / or FB / briefly and repeatedly until found a station.
Programming radio stations
You can store up to a total of 40 radio stations (FM and AM) in the memory, manually or automatically (Autostore)
1. Tune to your desired station
2. Press PROGRAM / to activate programming, icon " MEMORY" and P01 will start flashing.
3. Press PRESET + / or PRESET – / to allocate a number from 1 to 20 stations.
4. Press PROGRAM / to confirm, display shows the preset number waveband and the frequency of the preset station.
5. Repeat steps 1-4 to store other stations to listen to a preset station. Press PRESET + /
or more until the desired preset station in displayed.
To listen to a preset station
Press PRESET + / or PRESET – /
once or more until the desired preset station in displayed.
Automatic programming radio stations Automatic programming will station preset 1, from this preset number upwards,
former programmed tuner stations will be erased.
until frequency begins to scroll the radio automatically tunes to a
or PRESET – /
1. Press and hold PROGRAM /
- Icon " memory" will start flashing
- Available stations are programmed
- After all stations are stored, the last preset station will then be played
ANTENNA
Antenna: for FM reception, the unit is provided with a FM WIRE ANTENNA, move the wire until the reception is clear
and with no interferences. For AM reception, the unit is provided with a directional build-in ferrite antenna. Rotate the set
to find the position in which the best reception is obtained. Do not connect the EXTERNAL FM ANTENNA to any outside
antenna.
USB & SD-CARD OPERATION
USB operation:
1. Press the FUNCTION /
2. Plug-in USB mass storage device. READ is displayed as the system scans the contents of USB device.
3. Track no. 1 of root folder (Folder 1) will be playback automatically after finish reading USB device contents.
4. Press FF / or FB /
once or repeatedly until the desired track number appears in display.
5. Press PRESET + / or PRESET – /
6. Press STOP/BAND / to stop playback.
SD-Card operation:
1. Press the FUNCTION /
2. Insert SD-Card into the card slot. "READ" is displayed as the system scans the contents of SD card.
3. Track no. 1 of root folder (Folder 1) will be playback automatically after finish reading SD card contents.
4. Press FF / or FB /
5. Press PRESET + / or PRESET – /
6. Press STOP/BAND / to stop playback.
Remarks:
1) USB connector does not support connection with USB extension cable .
once
2) This unit is not designed for communication with computer directly.
3) It is not guarantee that all USB memory devices and SD cards will work on this audio system
IMPORTANT:
Do not disconnect the USB device during USB mode, as this may damage the external device or its files. Please power
off first or press another Mode before safely disconnecting the USB device.
USB Specification:
Interface
- USB 2.0 Full speed, HOST (USB HUB is not supported) Corresponding Flash memory
- Compatible with MPEG Audio 1, 2, 2.5
- Compatible with Layer 1, 2, 3
- Compatible with Bit rate: 128 – 320 Kbps
- Subfolder nest : 8 levels
- Number of track / titles max 999
- Support ID3 tag V2.0
button until Auto appears
to set the unit to USB mode.
to select desired album.
to set the unit to CARD mode.
once or repeatedly until the desired track number appears in display.
to select desired album.