Ricatech RR2000 User Manual page 6

TURNTABLE
PREPARING TO USE THE TURNTABLE
1. Remove black tie-wrap by untwisting and gently sliding out from TONE ARM .
2. Remove white protective needle cover by gently pulling towards front of unit.
3. Release TONE ARM and hold-down clip by gently pushing to the right. This will unlock tone arm from its ARM REST.
Re-lock the hold-down clip when moving the unit to another location.
TURNTABLE OPERATION
1. Press the FUNCTION / to set the unit to PHONO mode.
2. Set the SPEED CONTROL SWITCH to the correct speed (33 1/3, 45 or 78 rpm) for the selected record.
3. Pull the TONE ARM slightly to the right side until hear the "click" sound to activate the turntable.
4. Move the tone arm over the record and lower it to the point you want the record to start.
5. At the end of the record, the TONE ARM will stop automatically. You must return it to the TONE ARM REST by hand.
ACCESSORY SUPPLIED:
Adaptor for 45 rpm records (if required)
To play a 45 rpm record, remove the adaptor by placing thumb & forefinger in recesses
and pulling it upwards. Then placing it on the SPINDLE. The record can then be placed on the turntable.
EARPHONE JACK OPERATION
Listening through Earphones / Headphones (not included)
CD PLAYER
Playing a CD
1. Press the FUNCTION / to set the unit to CD mode.
2. Press CD OPEN / CLOSE / to open the CD compartment
3. Insert a disc with the printed side facing up. Press CD OPEN / CLOSE /
is displayed as the CD player scans the contents of a disc.
4. Track no. 1 will be playback automatically after finish the reading CD disc contents.
5. Press FF / or FB / once or repeatedly until the desired track number appears in display.
6. Press STOP/BAND / to stop playback.
CD-MP3 disc playback
1. Insert CD-MP3 format disc. Press CD OPEN / CLOSE /
CD player scans the contents of a disc.
2. Track no. 1 of root folder (Folder 1) will be playback automatically after finish reading CD-MP3 disc contents.
3. Press FF / or FB / once or repeatedly until the desired track number appears in display.
4. Press PRESET + / or PRESET – / to select desired album.
5. Press STOP/BAND / to stop playback.
Phones
The sound from all speakers is cut off.
. again to close the compartment, READ
again to close the compartment. READ is displayed as the
PROGRAMMING TRACKS
You may store up to 20 tracks in the desired sequence.
1. In the stop position, press PROGRAM / to start programming. Icon "MEMORY" and P0-01 start flashing.
2. Press FF / or FB / once or repeatedly until the desired track number appears in the display. For MP3:
press PRESET + / or PRESET – / to select the desired album.
3. Press PROGRAM / to confirm, display shown stored track no. and next store position.
4. Repeat step 2-3 to select and store all desired tracks. FULL is displayed if you attempt to program more than 20 tracks
5. Press PLAY/PAUSE /
to play the program.
Erasing the program
You can erase the contents of the memory by:
- once if in stop position, twice during playback;
- Press POWER /
- Select another sound source
- Open the CD door
RECORDING
From CD to SD/USB
The system is capable to convert whole CD disc to MP3 format and copy to USB mass storage device or SD card. And
also have the ability to copy one single MP3 track to and from on USB/SD card.
1. In CD playback mode, press REC / to start ripping to USB/SD card (default USB if both device are detected),
playback will be stopped and skipped back to the beginning of current track, system will scan the contents of USB/SD
card and create folder to store MP3 track. Resume CD playback and start ripping from the moment. The corresponding
target device icon " USB " / " CARD " start flashing.
2. Press STOP/BAND / to exit CD ripping.
MP3 copying
1. In CD-MP3, USB or SD card playback mode, press REC /
to SD card or vice versa. Playback will be stopped and system will scan the contents of USB/SD card and create
folder to store MP3 track.
2. icon " REC displayed
3. Message COPY 01 will be displayed, the proportional copied percentage will be shown on the decimal number.
4. The target device icon "USB" or "CARD" start flashing, the decimal number will be increment from 01 as MP3 copying
starts, the process will stop as it reach 100
5. Current MP3 will be playback from beginning
From Phono to SD / USB
The system is capable to convert audio signal from PHONO input to MP3 format and store in USB mass storage device
or SD card (default USB if both devices are detected)
1. Press the FUNCTION / to set the unit to PHONO mode.
2. Press REC / to start ripping, the system will scan the contents of USB/SD card and create folder to store MP3
tracks.
3. Icon " REC " and message " RIPP TO" are displayed, icon " PHONO " start flashing.
4. The target device icon " USB " or " CARD " start flashing as ripping begins.
5. Press STOP/BAND / to exit PHONO ripping
to start MP3 copying from CD to USB/SD card, or USB