Table of Contents
Related Manuals for Patton EdgeRoute 6081RC
Summary of Contents for Patton EdgeRoute 6081RC
- Page 1 Model 6081RC EdgeRoute Network Access Server User Manual Sales Office: +1 (301) 975-1000 Technical Support: +1 (301) 975-1007 E-mail: support@patton.com WWW: www.patton.com Part Number: 07MD6081RC-GS, Rev. D Revised: February 20, 2012...
- Page 2 Copyright © 2012, Patton Electronics Company. All rights reserved. The information in this document is subject to change without notice. Patton Electronics assumes no liability for errors that may appear in this document. The software described in this document is furnished under a license and may be used...
-
Page 3: Summary Table Of Contents
Summary Table of Contents Model 6081RC overview ..........................12 Hardware installation............................ 20 Initial configuration ............................28 Contacting Patton for assistance ........................32 Compliance information ..........................35 Specifications ..............................38 Cabling ................................. 41 Port pin-outs ..............................44 End user license agreement... -
Page 4: Table Of Contents
LED display ..............................19 Hardware installation............................ 20 Introduction ................................21 Unpacking the Model 6081RC ..........................21 Installing the PMC Ethernet Access Module onto the 6081RC front blade ............22 Model 6081RC blades installation.........................23 Cable installation..............................25 Connecting the Ethernet ports ........................25 Connecting the 10/100Base-T Ethernet port to an Ethernet switch or hub ..........26... - Page 5 Model 6081RC Network Access Server User Manual Initial configuration ............................28 Introduction ................................29 1. Connecting the 6081RC to your PC .........................29 Connecting and logging in via the Ethernet port .....................29 Connecting and logging in via the Console port .....................30 2. Configuring the desired IP address ........................30...
- Page 6 Model 6081RC Network Access Server User Manual Console .................................42 Ethernet ................................43 Port pin-outs ..............................44 Introduction ................................45 Console port................................45 Ethernet ................................46 End user license agreement ........................... 47 End User License Agreement ..........................48 1. Definitions ..............................48 2. Title ................................48 3. Term ................................48...
-
Page 7: List Of Figures
Connecting the 6081RC to your laptop PC via the Ethernet port ...... -
Page 8: List Of Tables
List of Tables General conventions ..............10 Mouse conventions . -
Page 9: About This Guide
Appendix D describes the router’s ports and pin-outs • Appendix E provides license information that describes acceptable usage of the software provided with the 6081RC For best results, read the contents of this guide before you install the Model 6081RC. -
Page 10: Precautions
Model 6081RC Network Access Server User Manual Precautions Notes and cautions, which have the following meanings, are used throughout this guide to help you become aware of potential Model 6081RC problems. Warnings relate to personal injury issues, and Cautions refer to potential property damage. Note Calls attention to important information. -
Page 11: Mouse Conventions
Model 6081RC Network Access Server User Manual Table 1. General conventions Convention Meaning < > Angle brackets indicate function and keyboard keys, such as <Shift>, <Ctrl>, <C>, and so on. All system messages and prompts appear in the Courier font as the Are you ready? system would display them. -
Page 12: Model 6081Rc Overview
Chapter 1 Model 6081RC overview Chapter contents Introduction ................................13 Product overview ..............................13 Hardware overview ..............................15 LAN Ethernet port ............................17 Packet switched Ethernet bus (PSB) ........................17 Backplane Ethernet interfaces .........................17 RS-232 control port ............................18 Power system ..............................18 Central processing unit ...........................18 Temperature ..............................18... -
Page 13: Introduction
Access Infrastructure System (AIS). With hardware and software features optimized for Layer-2/Layer-3 net- working, the 6081RC enables the AIS to deliver IP as an access infrastructure element as well as support the delivery of advanced broadband IP services and applications. - Page 14 TDM applications. The 6081RC connects directly to all channels (4,096) on the H.110 bus and is agnostic to the line interface method. The current set of compatible ForeFront resources which interface to the 6081RC include: •...
-
Page 15: Hardware Overview
Model 6081RC Network Access Server User Manual 1 • Model 6081RC overview The 6081RC’s applications give life to the hardware features of the 6081RC. Details of the software applica- tions are indicated in the section 6081RC IP Access Server Functionality. -
Page 16: Model 6081Rc Front Panel
Model 6081RC Network Access Server User Manual 1 • Model 6081RC overview Handle Mezzanine Card Interface 1 Mezzanine Card Interface 2 L2 LINK 10/100 ENET port ENET CONFIG port READY Handle Figure 2. Model 6081RC front panel • One front panel 10/100Mbps Ethernet port (see... -
Page 17: Lan Ethernet Port
Model 6081RC Network Access Server User Manual 1 • Model 6081RC overview LAN Ethernet port Front panel 10/100-Mbps Ethernet LAN port labeled ENET (ETH0) is presented on a RJ-45 connector with an auto-sensing/full-duplex 10Base-T or 100Base-T interface. Also included are: •... -
Page 18: Rs-232 Control Port
B and C. Redirecting an Ethernet port to the front panel disables the backplane interface for that port. RS-232 control port The RS-232 port provides for initial configuration of the Model 6081RC’s IP and gateway addresses. The RS- 232 port supports: •... -
Page 19: Led Display
Model 6081RC Network Access Server User Manual 1 • Model 6081RC overview • SYSLOG client • Remote software upgrade via FTP • Built-in HTTP server for complete configuration and control using a standard WWW browser L2 LINK Link/Traffic ENET 10/100 Mbps READY Figure 4. -
Page 20: Hardware Installation
Chapter 2 Hardware installation Chapter contents Introduction ................................21 Unpacking the Model 6081RC ..........................21 Installing the PMC Ethernet Access Module onto the 6081RC front blade ............22 Model 6081RC blades installation.........................23 Cable installation..............................25 Connecting the Ethernet ports ........................25 Connecting the 10/100Base-T Ethernet port to an Ethernet switch or hub ..........26... -
Page 21: Introduction
The Model 6081RC comes with the following items: The Model 6081RC rack card unit • • One RJ45-to-RJ45 cable for use with the console and Ethernet ports • A DB9-RJ45 (EIA-561) adapter for connecting a PC's serial port to the 6081RC console port Introduction... -
Page 22: Installing The Pmc Ethernet Access Module Onto The 6081Rc Front Blade
Installing the PMC Ethernet Access Module onto the 6081RC front blade You may purchase an optional PMC Ethernet Access Module for the Model 6081RC. The PMC Ethernet Access Module may be factory installed, or you may order it separately for installation in the field. The Model... -
Page 23: Model 6081Rc Blades Installation
3. Insert the front panel of the PMC card into the cutout for PMC slot 2 on the front panel of the Model 6081RC. 4. Align the two connectors on the PMC card with the corresonding connectors on the Model 6081RC (see figure 5 on page 22). -
Page 24: Alignment/Esd Pin And Card Handle
• A cold-water pipe • Building structural steel 1. If you have not done so already, remove the Model 6081RC from its shipping container. Note Be sure to wear the anti-static strap to prevent electrostatic damage to the blade. Note The location should be well ventilated. -
Page 25: Cable Installation
CAUTION mechanical serviceability. Connecting the Ethernet ports The Model 6081RC comes with three Ethernet ports. One Ethernet port is presented on the front panel via an RJ-45 connector (figure 7), and two internal Ethernet ports that connect to the PICMG 2.16 backplane for inter- card communication. -
Page 26: Connecting The 10/100Base-T Ethernet Port To An Ethernet Switch Or Hub
8. Connect a straight-through CAT-5 cable (one wired as shown in figure 8) between the Model 6081RC and the hub/switch. Figure 8. Ethernet RJ-45 pin and signal definitions for Model 6081RC Connecting the 10/100Base-T Ethernet port to an Ethernet-capable workstation or PC The 10/100Base-T Ethernet port can connect to a single Ethernet-capable workstation or PC by means of a cross over cable. -
Page 27: Connecting The Eia-561 Rs-232 Configuration Port (Dce Configured)
DB-9-to-RJ-45 cable Completing the hardware installation This section verifies that the Model 6081RC hardware is operational to the point where you can begin config- uring the software settings. Power is delivered from the chassis backplane through the power connectors on the 6081RC blades. Upon insertion into the ForeFront chassis, the Model 6081RC immediately powers up and begins its boot cycle. -
Page 28: Initial Configuration
Chapter 3 Initial configuration Chapter contents Introduction ................................29 1. Connecting the 6081RC to your PC .........................29 Connecting and logging in via the Ethernet port .....................29 Connecting and logging in via the Console port .....................30 2. Configuring the desired IP address ........................30... -
Page 29: Introduction
Model 6081RC Network Access Server User Manual 3 • Initial configuration Introduction This chapter leads you through the basic steps to set up a new 6081RC and to download a configuration. Set- ting up a new 6081RC consists of the following main steps: Note If you haven’t already installed the 6081RC, refer to Chapter 2,... -
Page 30: Connecting And Logging In Via The Console Port
31. Otherwise, refer to the following sections to change the address and network mask. Login To access the 6081RC, start the Telnet application. Type the default IP address for the router into the address field: 192.168.200.10. Accessing your 6081RC via a Telnet session displays the login screen. Type the factory default login: admin and password: <blank>. -
Page 31: Changing The Ip Address
3. Connecting the 6081RC to the network In general, the 6081RC will connect to the network via the LAN (ETH 0) port. The 6081RC is equipped with Auto-MDX Ethernet port, so you can use straight-through or crossover cables for host or hub/switch connec- tions. -
Page 32: Contacting Patton For Assistance
Chapter 4 Contacting Patton for assistance Chapter contents Introduction ................................33 Contact information..............................33 Warranty Service and Returned Merchandise Authorizations (RMAs)..............33 Warranty coverage ............................33 Out-of-warranty service ..........................33 Returns for credit ............................33 Return for credit policy ..........................34 RMA numbers ..............................34 Shipping instructions ..........................34... -
Page 33: Introduction
If you have ordered the wrong equipment or you are dissatisfied in any way, please contact us to request an RMA number to accept your return. Patton is not responsible for equipment returned without a Return Authorization. -
Page 34: Return For Credit Policy
RMA#: xxxx 7622 Rickenbacker Dr. Gaithersburg, MD 20879-4773 USA Patton will ship the equipment back to you in the same manner you ship it to us. Patton will pay the return shipping costs. Warranty Service and Returned Merchandise Authorizations (RMAs) - Page 35 Appendix A Compliance information Chapter contents Compliance ................................36 RTTE Directive (CE Mark) ..........................36 ................................36 Radio and TV Interference ............................36 FCC Part 68 (ACTA) Statement ...........................36 6081RCCE Declaration of Conformity.........................37 Authorized European Representative ........................37...
-
Page 36: A Compliance Information
The 6081RC router have been tested and found to comply with the limits for a Class A computing device in accordance with specifications in Subpart B of Part 15 of FCC rules, which are designed to provide reasonable protection from such interference in a commercial installation. -
Page 37: 6081Rcce Declaration Of Conformity
The safety advice in the documentation accompanying this product shall be obeyed. The conformity to the above directive is indicated by CE sign on the device. The signed Declaration of Conformity can be downloaded at www.patton.com/certifications. Authorized European Representative D R M Green European Compliance Services Limited. - Page 38 Appendix B Specifications Chapter contents Routing .................................39 RADIUS client..............................39 IP Services ................................39 Ethernet Ports ...............................39 Front Panel Indicators ............................39 Ethernet Services ..............................40 HDLC Services ..............................40 Management Service..............................40 Alarm Reporting..............................40 Safety..................................40 Physical .................................40...
-
Page 39: B Specifications
Model 6081RC Network Access Server User Manual B • Specifications Routing RIPv1 (RFC 1058) RIPv2 (RFC 2453) VLSM (RFC 1878) RADIUS client Authentication (RFC 2865 & 2868) Accounting (RFC 2866 & 2867) PAP (RFC 1332) CHAP (RFC 1334 & 1994) -
Page 40: Ethernet Services
Model 6081RC Network Access Server User Manual B • Specifications Ethernet Services 802.1q VLAN tagging Transparent passing of VLAN tagged Ethernet frames HDLC Services PPP (RFC 1661, 2153) LCP (RFC 1570, 2484) BCP (RFC 1638) IPCP (RFC 1332) Management Service... -
Page 41: Cabling
Appendix C Cabling Chapter contents Introduction ................................42 Console .................................42 Ethernet ................................43... -
Page 42: Introduction
Model 6081RC Network Access Server User Manual C • Cabling Introduction This section provides information on the cables used to connect the 6081RC and the interface cards to the existing network infrastructure and to third party products. Console The 6081RC can be connected to a serial terminal over its serial console port, as depicted in... -
Page 43: Ethernet
Ethernet Ethernet devices (10Base-T/100Base-T/1000Base-T) are connected to the 6081RC over a cable with RJ-45 plugs. The Ethernet port on the 6081RC is Auto-MDX use any straight or crossover cable to connect to hubs, switches, PCs or other devices. The interconnecting cables shall be acceptable for external use... -
Page 44: Port Pin-Outs
Appendix D Port pin-outs Chapter contents Introduction ................................45 Console port................................45 Ethernet ................................46... -
Page 45: Introduction
Model 6081RC Network Access Server User Manual D • Port pin-outs Introduction This section provides pin-out information for the ports of the 6081RC. Console port Configuration settings: 9600 bps, 8 bits, no parity, 1 stop bit, no flow control 8–RTS (N/C) 7–CTS (N/C) -
Page 46: Ethernet
Model 6081RC Network Access Server User Manual D • Port pin-outs Ethernet Table 5. RJ45 socket 10/100Base-T Signal Note Pins not listed are not used. Table 6. RJ45 socket 1000Base-T Signal TRD0+ TRD0- TRD1+ TRD1- TRD2+ TRD2- TRD3+ TRD3- Ethernet... -
Page 47: E End User License Agreement
Appendix E End user license agreement Chapter contents End User License Agreement ..........................48 1. Definitions ..............................48 2. Title ................................48 3. Term ................................48 4. Grant of License ............................48 5. Warranty ..............................48 6. Termination ..............................49 7. Other licenses .............................49... -
Page 48: End User License Agreement
Program(s), even if Patton Electronics Company has been advised of the possibil- ity of such damages. Because some states do not allow the exclusion or limitation of liability for consequential or incidental damages, the above limitation may not apply to you. -
Page 49: Termination
The End User may terminate this agreement by returning the Designated Equipment and destroying all copies of the licensed Program(s). Patton Electronics Company may terminate this Agreement should End User violate any of the provi- sions of section “4. Grant of License”...