Related Manuals for Dri-Air Industries ARID-X
Summary of Contents for Dri-Air Industries ARID-X
- Page 1 DRI-AIR INDUSTRIES, INC. ARID-X & HP4-X 18-100 FLOOR MOUNT DRYERS OPERATING MANUAL OPERATING MANUAL - ARID-X, HP4-X 18-100 FM DRYERS Page 1 Revision 10/8/02...
- Page 2 DRI-AIR INDUSTRIES, INC. DRI-AIR INDUSTRIES, INC. 16 THOMPSON ROAD P.O. BOX 1020 EAST WINDSOR, CT 06088-1020 Tel. (860) 627-5110 (860) 623-4477 Internet http://www.dri-air.com e-mail: sales@dri-air.com Page 2 OPERATING MANUAL - ARID-X , HP4-X 18-100 FM DRYERS Revision 10/8/02...
-
Page 3: Table Of Contents
DRI-AIR INDUSTRIES, INC. CONTENTS DRYER OPERATION/FEATURES --------------------------- 4 AIR FLOW SCHEMATIC FOR ARID-X DRYERS -------- 6 AIR FLOW SCHEMATIC FOR HP4-X DRYERS --------- 7 DRYER CYCLE DIAGRAM ------------------------------------ 8 PLC STANDARD ELECTRICS ------------------------------- 9 INSTALLATION PROCEDURE ----------------------------- 10 Electrical Connection ------------------------------------- 10... -
Page 4: Dryer Operation/Features
DRI-AIR INDUSTRIES, INC. The ARID-X dryer series is a dual bed design that provides a DRYER OPERATION/ constant supply of dry air to the material hopper. While one FEATURES bed is removing moisture from the process air the other is regenerating by heating the desiccant to a high temperature. - Page 5 INDUSTRIES, INC. DRYER OPERATION/ FEATURES (Cont.) Dryer Controls The ARID-X series can be supplied with the standard PLC Control Module or the advanced Microprocessor Control Module, while the HP4-X series is only available with the Microprocessor Control Module. The PLC Control module includes a PLC control board, display board, temperature controller and touch pad that is programmed for the drying cycle described above.
-
Page 6: Air Flow Schematic For Arid-X Dryers
S A FE TY TH ER M A L TO H O P P E R P R O C E S S H E AT E R (A P D 5-9) Page 6 OPERATING MANUAL - ARID-X , HP4-X 18-100 FM DRYERS Revision 10/8/02... -
Page 7: Air Flow Schematic For Hp4-X Dryers
F O R P L C C O N T R O L O N LY T O H O P P E R P R O C E S S H E AT E R (H P D 5 -9 ) OPERATING MANUAL - ARID-X, HP4-X 18-100 FM DRYERS Page 7 Revision 10/8/02... -
Page 8: Dryer Cycle Diagram
DRI-AIR INDUSTRIES, INC. DRYER CYCLE DIAGRAM Page 8 OPERATING MANUAL - ARID-X , HP4-X 18-100 FM DRYERS Revision 10/8/02... -
Page 9: Plc Standard Electrics
EXPANDER BD REV C PO WER U N U SED U N U SED H I TEM P M AIN SAFETY TEM P 50-300 N O N H .P. OPERATING MANUAL - ARID-X, HP4-X 18-100 FM DRYERS Page 9 Revision 10/8/02... -
Page 10: Installation Procedure
DRI-AIR INDUSTRIES, INC. For all Dri-Air models except ARID-X 10, AHM-1, & PDII INSTALLATION PROCEDURE Electrical Connection: Open electrical access door on the front of the machine by turning the disconnect off and turning the lower clamping screw 1/2 turn counterclockwise. Locate the disconnect by following the operating handle down to the electrical panel. -
Page 11: Start-Up Procedure
Press SET again to enter the new temperature. If the display flashes, the temperature is out of the control range. If the display shows 0000 the thermocouple is not connected or is faulty. OPERATING MANUAL - ARID-X, HP4-X 18-100 FM DRYERS Page 11 Revision 10/8/02... -
Page 12: Microprocessor Control
For a more detailed explanation of the features and operation of the Microprocessor Controller, please consult the Microprocessor Control Operating manual enclosed with this unit. Page 12 OPERATING MANUAL - ARID-X , HP4-X 18-100 FM DRYERS Revision 10/8/02... -
Page 13: Dryer Operation-Trouble Shooting
5. Operating Conditions: a. Check the process temperature. It should not be set below 140° F (60° C) because the unit will go into high temp alarm. OPERATING MANUAL - ARID-X, HP4-X 18-100 FM DRYERS Page 13 Revision 10/8/02... -
Page 14: Dryer Operation-Detailed Diagnosis
A. Check fuses on power board B. Check solid state relays on power board. C. Check that the air flow is correct. D. Check blower rotation E. Check heater for continuity. Page 14 OPERATING MANUAL - ARID-X , HP4-X 18-100 FM DRYERS Revision 10/8/02... -
Page 15: Dri-Air Rotary Zone Valve
DO NOT PUT FINGERS INTO VALVE WITH POWER ON Check all electrical connections to make sure they are tight. Contact factory with the serial number of the dryer for a replacement valve. OPERATING MANUAL - ARID-X, HP4-X 18-100 FM DRYERS Page 15 Revision 10/8/02... -
Page 16: Parts Lists
Dewpoint Sensor 81908 81908 208V 230V 400V 480V 575V HEATERS Regeneration (Cone Style) 83342 83373 83982 83374 84235 HP Center (Flat Style) 82373 82373 83958 82505 84260 Process Page 16 OPERATING MANUAL - ARID-X , HP4-X 18-100 FM DRYERS Revision 10/8/02... -
Page 17: Arid-X & Hp4-X 50 - 100
Dewpoint Sensor 81908 81908 230V 400V 480V 575V HEATERS Regeneration (Cone Style) 81351 81766 81366 81432 HP Center (Flat Style) 82364 83934 82493 83372 Process 82343 84204 82319 84065 OPERATING MANUAL - ARID-X, HP4-X 18-100 FM DRYERS Page 17 Revision 10/8/02... - Page 18 DRI-AIR INDUSTRIES, INC. NOTES: Page 18 OPERATING MANUAL - ARID-X , HP4-X 18-100 FM DRYERS Revision 10/8/02...
- Page 19 DRI-AIR INDUSTRIES, INC. NOTES: OPERATING MANUAL - ARID-X, HP4-X 18-100 FM DRYERS Page 19 Revision 10/8/02...
- Page 20 DRI-AIR INDUSTRIES, INC. NOTES: Page 20 OPERATING MANUAL - ARID-X , HP4-X 18-100 FM DRYERS Revision 10/8/02...
Need help?
Do you have a question about the ARID-X and is the answer not in the manual?
Questions and answers