DriSteem VAPORMIST Installation Instructions And Maintenance Operations Manual
  1. Manuals
  2. Brands
  3. DriSteem Manuals
  4. Humidifier
  5. VAPORMIST
  6. Installation instructions and maintenance operations manual
DriSteem VAPORMIST Installation Instructions And Maintenance Operations Manual

DriSteem VAPORMIST Installation Instructions And Maintenance Operations Manual

Electric steam humidifiers
Hide thumbs Also See for VAPORMIST:
Table of Contents

Advertisement

Quick Links

See also: Installation, Operation & Maintenance Manual
READ AND SAVE THESE INSTRUCTIONS
®
VAPORMIST and
®
VAPORMIST DI
ELECTRIC STEAM HUMIDIFIERS
For Ducted or Ductless Applications
Installation Instructions
and
Maintenance Operations
Manual
UL LISTED
CUL LISTED
ä

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the VAPORMIST and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for DriSteem VAPORMIST

Summary of Contents for DriSteem VAPORMIST

  • Page 1 READ AND SAVE THESE INSTRUCTIONS ® VAPORMIST and ® VAPORMIST DI ELECTRIC STEAM HUMIDIFIERS For Ducted or Ductless Applications Installation Instructions Maintenance Operations Manual UL LISTED CUL LISTED ä...

  • Page 2: Table Of Contents

    Familiarizing yourself with this manual will help you to ensure proper operation of the equipment for years to come. This manual covers the installation and maintenance procedures for both the VAPORMIST AND VAPORMIST DI humidifiers.

  • Page 3: Vapormist Diagrams

    Removable Slide assembly under evaporating chamber Evaporating provides easy removal for cleaning Chamber OM-287 Figure 3-2: VAPORMIST DI Humidifier (Deionized Water) The VAPORMIST DI humidifier 1-½" or 2" Flexible vapor shown here is specifically designed hose connects to for use with deionized or reverse dispersion tube induct.

  • Page 4: Installation

    Humidifier tions are made at the lower right rear corner of the unit. The VAPORMIST humidifier is designed to hang on a wall, and should be installed in a mechanical room or in When mounting on a stud wall (studs 16" on center), a space located near an air duct system.

  • Page 5: Mounting Dispersion Tube With Condensate Drain Line

    INSTALLATION ® VAPORMIST Mounting Tube Figure 5-1: Single Tube with Condensate Drain Line Insertion Length • Mount dispersion tube level. • For best vapor absorption, orient dispersion tube so that tubelets are 2.5" Pre-molded High directed against the air flow.

  • Page 6: Piping And Wiring

    WIRING All wiring must be in accordance with all governing ® codes, and with VAPORMIST or VAPORMIST DI wiring diagrams. The diagram is located inside the removable front panel on the right-hand side of the...

  • Page 7: Electrical Specifications And Capacities/Dimensions

    On 208/240 single phase (3 wire) and 3 phase (4 wire) supplies, the neutral line may be utilized for 120 volt when used in conjunction with SDU fan unit. ** For wire sizing. Highest leg draw is shown due to current unbalance in some cases. All VAPORMISTS operate 50/60 Hz. Top View Figure 8-1: VAPORMIST Unit Dimensions (All measurements shown in inches.) 16.000...

  • Page 8: Area-Type Application Using Space Distribution Unit (Sdu)

    Mounting the SDU The SDU may be placed directly on top of the VAPORMIST cabinet or it may be mounted on a wall. A wall mounting bracket and two 3/8" lag bolts are provided with each fan unit. (See page 4 for mounting instructions.)
  • Page 9 (ft.)* (ft.)* (ft.)* (ft.)* independently of the VAPORMIST humidifier. A wiring diagram of the SDU is included with the unit. On a call for humidity, the humidifier will begin producing steam and the start relay will energize the SDU blower.

  • Page 10: Start-Up And Operation

    Figure 10-1: Electronic Probe Control for does in a steam boiler. This simple device greatly Maintaining Proper Water Level (VAPORMIST ® reduces the frequency of cleaning the evaporating Only) chamber.
  • Page 11 VAPORMIST. Any leaks should be above 60 psi and/or water hammer would be objection- sealed. able, a pressure-reducing valve or shock arrester should be installed. Even though the VAPORMIST has an internal 1" air gap, some local codes may require a vacuum breaker.

  • Page 12: Maintenance Procedure

    6. Unscrew the probe housing, and remove any mineral build-up accumulated in the housing. Mineral Precipitate As evaporation takes place in a standard VAPORMIST 7. Clean the probe-rod assembly. Scrape off build-up unit, the minerals dissolved in the water come out of...
  • Page 13 14. Replace front panel and turn on electric power. DISCONNECT ANY OF THE ELECTRICAL CONDUITS. 15. VAPORMIST DI is again ready to humidify. 7. Slide the evaporating chamber forward on the track. Off-Season Shut-Down Procedure Remove the cover of the chamber, raise and slide 1.

  • Page 14: Vapormist Trouble-Shooting Guide

    ® VAPORMIST TROUBLE-SHOOTING GUIDE CONTROL PANEL LIGHTS PROBLEM FILL READY DRAIN POSSIBLE CAUSE RECOMMENDED ACTION WATER Humidifier will Control transformer Verify control voltage across secondary not heat leads of transformer. Reset transformer circuit breaker. Humidistat is not calling Set humidistat to call. Inspect for faulty humidistat.

  • Page 15: Vapormist Di Trouble-Shooting Guide

    ® VAPORMIST DI TROUBLE-SHOOTING GUIDE READY POSSIBLE CAUSE RECOMMENDED ACTION PROBLEM WATER Humidifier will Control transformer Verify control voltage across secondary leads of not heat transformer. Reset transformer circuit breaker. Set humidistat to call. Inspect for faulty humidistat. Humidistat is not calling Safety controls open Check safety control.

  • Page 17: Replacement Parts

    REPLACEMENT PARTS Table 17-1: VAPORMIST (see drawing on page 16) No. Description Qty. Part No. Tank 160012* Cover Thermo Cut-Out 409560-001 Cover, Heater Terminal 160750* Gasket, Cover 160695* Heater 409600* Knob, T-Handled Utility 700725 Connector, 3/8" flex. 407127-038 Valve, ¼" Solenoid Fill...
  • Page 19 REPLACEMENT PARTS Table 19-1: VAPORMIST DI (see drawing on page 18) No. Description Qty. Part No. Tank 160012* Cover Thermo Cut-Out 409560-001 Cover, Heater Terminal 160750* Gasket, Cover 160695* Heater 409600* Knob, T-Handled Utility 700725 Elbow, ¼" 90° (VMDI 2-16)
  • Page 20 REPLACEMENT PARTS Table 20-1: Subpanel for VAPORMIST and VAPORMIST DI No. Description Qty. Part No. Transformer, 120V, 24V Sec., 75 VA 408960 Transformer, 208/240/480V, 24V Sec., 75 VA 408965 Contactor, 24V, 30 amp 407001-007 Contactor, 24V, 50 amp 407001-009 Terminal Block, 3-Pole...

  • Page 21: Maintenance Service Record

    MAINTENANCE SERVICE RECORD DATE INSPECTED PERSONNEL OBSERVATION ACTION PERFORMED...

  • Page 22: Two-Year Limited Warranty

    Continuous product improvement is a policy of DRI-STEEM therefore, product features and specifications are subject to change without notice. ä 14949 Technology Drive • Eden Prairie, MN 55344 Telephone: 1-800-328-4447 • In MN: (612) 949-2415 Fax: (612) 949-2933 • E-Mail: sales@dristeem.com Printed on recycled paper with 3ULQWHG RQ UHF\FOHG SDSHU ZLWK DJULEDVHG LQNV agri-based inks. Minimum 10% Post Consumer Waste.

This manual is also suitable for:

Vapormist di

Table of Contents