Advertisement
3.2.2 ASSEMBLY/DISASSEMBLY OF CABINET PARTS AND ELECTRICAL PARTS
Disassembly procedure
STEP
Fig.
PART NAME
No.
No.
[1]
B.COVER ASSY
FA1
[2]
GRIP LOWER ASSY
FA2
[3]
BKT(HDD)ASSY
FA3
[4]
COVER(BELT) ASSY
FA4
[5]
TOP COVER ASSY
FA5
[6]
ZOOM UNIT
[7]
REAR COVER ASSY
FA6
[8]
UPPER ASSY
FA7-1
[9]
OPERATION BOARD ASSY
FA7-2
[10]
U.CASE(U) ASSY
FA7-3
[11]
POWER SW ASSY
[12]
COVER(HINGE)ASSY
FA7-4
[13]
MONITOR ASSY
[14]
SPEAKER
FA7-5
[15]
F. COVER ASSY
FA8
[16]
MIC
[17]
HOOD
FA9
[18]
MAIN BOARD ASSY
[19]
OP FRAME ASSY
FA10
NOTE2a:
During the procedure, leave the GRIP BELT removed from the hook.
NOTE2b:
During the procedure, be careful not to break the tabs(L2a-c).
NOTE3a:
Be careful in handling this part.
Pay special attention not to give shocks.
NOTE3b:
When attaching, be careful with the GEL lift.
NOTE5:
During the procedure, leave the JACK COVER open.
NOTE7:
During the procedure, leave the MONITOR COVER open.
NOTE8:
During the procedure, be careful not cut the SPEAKER WIRE.
Place the WIRE through the space.
NOTE9a:
During the procedure, be careful not to lose KNOB(V/O).
NOTE9b:
During the procedure, be careful not to break or deform the parts.
NOTE9c:
When attaching, be careful with the positions of the two
switches (S401, S403). Attach the POWER SW (S401) by
pulling it to the position indicated with the arrow, and attach
the SWITCH LEVER to the "OFF" position.
Attach both the MODE SWITCH (S403) and the SWITCHING
LEVER by pulling to the positions indicated with the arrows.
After attachment, check whether the operation is normal by
operating the SWITCHING LEVER.
NOTE18:
During the procedure, drop the MAIN BOARD ASSY into this slit.
Destination of connectors
CN.NO.
CONNECTOR
CN3
HDD
CN5
MAIN
CN104
CN7
MAIN
CN103
CN8a
MAIN
CN109
CN8b
MAIN
CN101
CN9
OPERATION
CN402
CN15
MAIN
CN107
CN18a MAIN
CN106
CN18b MAIN
CN105
POINT
NOTE
5(S1),2(L1)
GRIP BELT,2(S2),2(L2a),L2b,2(L2c)
NOTE2a,b
CN3
NOTE3a,b
2(S4a),3(S4b)
RING,WINDOW(W.B.S),2(S5),CN5,L5
NOTE5
2(S6),2(L6)
4(S7),CN7
NOTE7
3(S8),L8a,CN8a,b,L8b
NOTE8
4(S9),CN9,2(L9)
NOTE9a,b,c
2(S10),L10a,b
2(S11),L11
2(S12),2(L12)
2(S13),2(L13)
4(S14),L14,BKT(UPPER)
S15,L15a,2(L15b),CN15
2(S16),2(L16),BKT(MIC)
2(S17),L17a,b
S18,L18a,b,CN18a,b
NOTE18
3(S19),FRAME ASSY
-
MAIN
CN102
ZOOM UNIT
-
REAR
CN6001
SPEAKER
-
OPERATION
CN401
MONI-BL
CN7601,7602
MIC
-
OP BLOCK
-
CCD
CN5001
-
-
-
-
-
-
-
-
-
-
-
-
<NOTE2b>
L2a
SPACER
NOTE2a
GRIP BELT
7
(S2)
PIN
NO.
40
6
45
2
45
24
4
22
24
4
5
(S1)
3
(S1)
(S1)
1
(S1) 2
(S1)
fig.1
Fig.FA1
6
L2b
(S2)
L2b
L2a
GEL
Fig.FA2
[1]
L1
NOTE2b
[2]
L2c
HOOK
(No.YF110)1-7
Advertisement
