Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Atrie DB108
Summary of Contents for Atrie DB108
-
Page 1: User Manual
Atrie DB108Ethernet User Manual Atrie DB108 ADSL MODEM User Manual V1.0... -
Page 2: Table Of Contents
Atrie DB108Ethernet User Manual CONTENTS 1.OVERVIEW............................... 3 1.1 ABOUT ADSL............................3 1.2 ABOUT ADSL2/2+..........................3 1.3 FEATURES............................3 2 SPECIFICATION.............................. 4 2.1 INTERFACE INTRODUCTION ......................4 2.1.1 INDICATOR AND INTERFACE....................4 2.1.2 SPLITTER SPEC........................... 4 2.2 HARDWARE CONNECTION ......................4 2.3 LED STATUS INDICATION........................ -
Page 3: Overview
Atrie DB108Ethernet User Manual 1.OVERVIEW 1.1 ABOUT ADSL An ADSL MODEM is a broadband Internet access device, which utilizes the high frequency segment of the phone line to transmit high-speed data without affecting the voice transmission. The frequency of the ADSL signal is higher than that of voice, so voice and ADSL signal can coexist in one line by using a splitter to insulate each from the other. -
Page 4: Specification
Atrie DB108Ethernet User Manual 2 SPECIFICATION 2.1 INTERFACE INTRODUCTION 2.1.1 NDICATOR AND INTERFACE Table 2.1 ITEM Name State introduction POWER A steady red light means the power connection works properly LINK Yellow, shows DSL line status. Indicator Green, Flashing means the Modem is transmitting or receiving... -
Page 5: Led Status Indication
Atrie DB108Ethernet User Manual Introduction： 1、 Use a telephone cord to connect the LINE port of the splitter with the RJ-11 port (the phone jack) on the wall. 2、 Use another telephone cord to connect the ADSL port of the splitter with the LINE port of the ADSL Modem. -
Page 6: Configuration
Atrie DB108Ethernet User Manual 3.CONFIGURATION 3.1 DEFAULT CONFIGURATION ADSL MODEM has pre-configured with the following VCI/VPI. The default dial-up mode is bridge encapsulation. For bridge mode, no need to configure any more parameter. However, the third party dial-up software is needed for connection with the Internet Tabel 3.1... -
Page 7: Save Setting
Atrie DB108Ethernet User Manual SAVE SETTING 3.3.2 After getting through each page for parameters setting, click “Save” or “Save apply” to store the value in ADSL MODEM. Briefly, we named “Save”. Note ： When you save the settings, the web page will be refreshed slowly, please wait it finished. - Page 8 Atrie DB108Ethernet User Manual Click on the next connection which you want modify. Press “Edit” button, enter the configure guide, as Figure 3.3 Figure 3.3 The value for VPI/VCI is assigned by your ISP. After inputting the PVC value, press “Next” into “connection type”.
-
Page 9: Rfc1483 Bridge Configuration
Atrie DB108Ethernet User Manual The Modem supports five ADSL protocol modes. Choose the protocol which is appointed by ISP and PVC encapsulation, click “Next” enter to the protocol configure. Below, we introduce the configuraion of the five protocol modes. • PPP over ATM (PPPoA) •... - Page 10 Atrie DB108Ethernet User Manual Figure 3.6 Note ： When you use bridge mode, please close “DHCP SERVER”, the result as Figure 3.7 Figure 3.7 Page 10 Total 17 Pages...
-
Page 11: Pppoe Configuration
Atrie DB108Ethernet User Manual 3.4.3 PPPOE CONFIGURATION PPPoE is also known as RFC 2516. It is a method of encapsulating PPP packets over Ethernet. PPPoA is also known as RFC2364 and named as Peer to Peer Protocol over ATM. As PPPoE, it also has all the features of PPP. -
Page 12: Static Address
Atrie DB108Ethernet User Manual Press “Next step” when configuration is finished. The following operation is same with Figure 3.5. Notice that PPPoE mode does not work until the modem is reset. 3.4.4 STATIC ADDRESS In Figure3.4, select MAC Encapsulation Routing (MER), press “Next”, and the configuration can be queried from your ISP, the result as Figure3.9. -
Page 13: Other Configuration
Atrie DB108Ethernet User Manual 4 OTHER CONFIGURATION 4.1 LAN CONFIGURATION Configuration of Modem’s IP address and password 4.1.1 CONFIGURATION OF MODEM’S IP ADDRESS As a network device, ADSL Modem has its own IP address and MAC address. The factory sets the MODEM, at a default IP address of 192.168.1.1 and subnet mask of 255.255.255.0. -
Page 14: Password Configuration
Atrie DB108Ethernet User Manual • Define the “Start IP address” and the “End IP address” of DHCP server (for example, from 192.168.1.2 to 192.168.1.254). • Input the value of lease (Measured by the second, 0 indicates permanently valid). As Figure 4.2, open DHCP server, computer will set the IP Address of network card with one of the address 10.10.10.11 ～... -
Page 15: Troubleshooting
Atrie DB108Ethernet User Manual 5. TROUBLESHOOTING 5.1 UNABLE TO ACCESS INTERNET 5.1.1 CHECK THE LINE AND THE DEVICE 1、 Check the indicator of power supply is on, if not, Make sure the connection of power supply is correct; Make sure the output of power supply is correct; Make sure the switch of power supply is turned on；... -
Page 16: Annex：shipping List
Telephone Line ×2 Atrie Technology Pvt. Ltd. Corporate office: Atrie House, # 591,3 Block, Koramangala, Bangalore -560 034 India Registered office: #B-121,Ground Floor ,Kalkaji, New Delhi – 110019 Regional office (West): #C/312,3rd Floor, Gokul Arcade, Vile Parle(E) Subhash Road,Mumbai - 400057 Web: http://www.atrieindia.com... - Page 17 Atrie DB108Ethernet User Manual Page 17 Total 17 Pages...
Need help?
Do you have a question about the DB108 and is the answer not in the manual?
Questions and answers