Advertisement
Quick Links
PORTSMOUTH™
Spread Lavatory Faucet
with Speed Connect™ Drain
Congratulations on purchasing your
American Standard faucet with
Speed Connect drain, a feature found
onlyon American Standard faucets.
Speed Connect Drain*
• Fewer parts, installs in less time
• Never needs adjustment
• Guaranteed to seal properly the first time, every time.
*Your new American Standard faucet is designed to work only with the Speed Connect drain.
Heplful tips for removing your current drain can be found in the Troubleshooting section of these instructions.
To ensure that your installation proceeds smoothly-please read these instructions carefully
before you begin.
Recommended tools
Screwdriver
1
INSTALL SPOUT
Insert SPOUT (1) and CABLE CONNECTOR (12) through center hole, making sure
the SEAL WASHER (3) is properly seated in the SPOUT ESCUTCHEON (2).
Assemble RUBBER WASHER (4), BRASS WASHER (5) and LOCKNUT (6) onto SPOUT
SHANK (7) from under side of sink . Make sure SPOUT (1) is centered in the mounting
hole and the slot in the BRASS WASHER (5) faces toward the rear of the sink.
Tighten LOCKNUT (6) firmly. Fig. A.
1A
INSTALL VALVE BODY
Place RUBBER RING (9) into ADAPTER (10).
Install LOCKNUT (11) onto VALVE BODY (8).
From under side of mounting surface, install VALVE BODY (8) through valve
mounting holes. Threads of VALVE BODY (8) should extent at least 5/16
of a inch above mounting surface top. Fig. B. Thread ADAPTER (10)
onto VALVE BODY (8) until snug against internal stop. If necessary, adjust
LOCKNUT (11).
Hand tighten LOCKNUT (11) to secure VALVE BODY (8).
Repeat above steps for opposite VALVE BODY (8A).
10
9
5/16'' MIN.
Fig. B.
Installation
Instructions
Channel Locks
Turn off hot and cold water
CAUTION
supplies before beginning.
MOUNTING
SURFACE
11
8
7420.801
7420.821
Series
7415.801
7415.821
Series
Adjustable Wrench
1
10
9
8
11
1
74 15
Certified to comply with ANSI A112.18.1
M 9 6 5 015 R E V. 1. 7
Tubing Cutter
Fig. A.
1
2
3
SLOT
8A
74 2 0
7
4
5
6
12
Advertisement
Related Manuals for American Standard Portsmouth 7415.801 Series
Summary of Contents for American Standard Portsmouth 7415.801 Series
- Page 1 • Guaranteed to seal properly the first time, every time. *Your new American Standard faucet is designed to work only with the Speed Connect drain. Heplful tips for removing your current drain can be found in the Troubleshooting section of these instructions.
- Page 2 POP-UP DRAIN Remove CLEAR PLASTIC COVER (1). Remove CARDBOARD SPACER (2) from under DRAIN POP-UP (3). Tighten TAILPIECE (4) on DRAIN BODY before Fig. B. installing DRAIN BODY. REMOVE FLANGE Thread FLANGE (1) counter-clockwise and remove FLANGE (1) and FOAM GASKET (2) from drain Fig.
- Page 3 ATTACH CABLE CONNECTOR Thread CABLE CONNECTOR (1) clockwise onto DRAIN BODY CONNECTION (2) and hand tighten. Fig. A. Your new POP-UP DRAIN installation is now complete. Fig. B. Note: Tailpeice on pop-up drain is 1-1/4” O.D. Fig. B. CHECK OPERATION OF POP-UP Operate LIFT KNOB (1) to verify that STOPPER (2) opens and closes.
-
Page 4: Install Handles
INSTALL HANDLES Push ADAPTER (1) on VALVE STEM (2), so that the hole of the ADAPTER (1) with the spline is facing up. Fig. A. Tighten STEM SCREW (3) to secure ADAPTER (1). Find correct position of LEVER HANDLE ASSEMBLY (4) by adjusting male teeth on ADAPTER (1) to female teeth in HANDLE (4). -
Page 5: Cable Adjustment Procedure
Speed Connect™ Drain Troubleshooting Guide If sink does not hold water even though Stopper is in the “down” position: • Follow CABLE ADJUSTMENT PROCEDURE. If Stopper does not raise up fully or sink drains too slowly: • Follow CABLE ADJUSTMENT PROCEDURE. If you need to remove the Stopper: •... - Page 6 To install the stopper in “Unlocked” mode, insert the Stopper into the Drain so that the Plastic Loop is facing toward the front of the Sink and the American Standard logo is facing rear. Rotate Stopper slightly if necessary so that the Stopper slides all the way down.
- Page 7 M962946-YYY0A CROSS HANDLE M962937-YYY0A HANDLE M962592-0070A DECK ADAPTER KIT 918555-0070A HANDLE SCREW 918049-0070A ADAPTER 994053-0070A CARTRIDGE A906652-0070A ATTACHMENT NUT M953006-0070A TEE & HOSE KIT 024220-0070A SUPPLY NUT HOT LINE FOR HELP For toll-free information and answers to your questions, call: 1-800-442-1902 Weekdays 8:00 a.m.
- Page 8 M962946-YYY0A CROSS HANDLE M962947-YYY0A HANDLE M962592-0070A DECK ADAPTER KIT 918555-0070A HANDLE SCREW 918049-0070A ADAPTER 994053-0070A CARTRIDGE A906652-0070A ATTACHMENT NUT M953006-0070A TEE & HOSE KIT 024220-0070A SUPPLY NUT HOT LINE FOR HELP For toll-free information and answers to your questions, call: 1-800-442-1902 Weekdays 8:00 a.m.