Advertisement
Quick Links
PRINCETON
Centerset Lavatory Faucet with
Speed Connect™ Drain
Congratulations on purchasing your American Standard
faucet with Speed Connect drain, a feature found only on
American Standard faucets.
Speed Connect™ Drain*
• Fewer parts, installs in less time
• Never needs adjustment
• Guaranteed to seal properly the first time, every time.
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
Required tools
Screwdriver
1
INSTALL FAUCET
Turn off hot and cold water supplies before beginning.
Note: Putty is not required unless mounting surface
is uneven. Apply a bead of PUTTY along the edge of
the underside of the BODY (1) if required.
Insert FAUCET (1) and CABLE CONNECTOR (2) through
mounting holes of Sink or mounting surface.
Assemble LOCKNUTS (3) onto SHANKS (4) from under
side of Sink. Hand tighten firmly.
(HAND TIGHTEN)
Fig. B.
Channel Locks
Turn off water at
CAUTION
main supply.
Fig. A.
Fig. B.
3
4
MOUNTING
SURFACE
2
Installation
Instructions
4508.201
Adjustable Wrench
Fig. A.
1
PUTTY
(IF REQUIRED)
4
SINK OR
1
Certified to comply with ANSI A112.18.1
M 9 6 8 8 4 3 R e v . 1 . 2
Tubing Cutter
POP-UP
CABLE
2
3
Advertisement
Related Manuals for American Standard Centerset Lavatory Faucet with Speed Connect Drain 4508.201
Summary of Contents for American Standard Centerset Lavatory Faucet with Speed Connect Drain 4508.201
- Page 1 PRINCETON Centerset Lavatory Faucet with Speed Connect™ Drain Congratulations on purchasing your American Standard faucet with Speed Connect drain, a feature found only on American Standard faucets. Speed Connect™ Drain* • Fewer parts, installs in less time • Never needs adjustment •...
- Page 2 POP-UP DRAIN Remove CLEAR PLASTIC COVER (1). Remove CARDBOARD SPACER (2) from under DRAIN POP-UP (3). Tighten TAILPIECE (4) on DRAIN BODY before Fig. B. installing DRAIN BODY. REMOVE FLANGE Thread FLANGE (1) counter-clockwise and remove FLANGE (1) and FOAM GASKET (2) Fig.
- Page 3 ATTACH CABLE CONNECTOR Thread CABLE CONNECTOR (1) clockwise onto DRAIN BODY CONNECTION (2) and hand tighten. Fig. A. Your new POP-UP DRAIN installation is now complete. Fig. B. Note: Tailpeice on pop-up drain is 1-1/4” O.D. Fig. B. CHECK OPERATION OF POP-UP Operate LIFT KNOB (1) to verify that STOPPER (2) opens and closes.
-
Page 4: Care Instructions
TEST INSTALLED FITTING With HANDLES (1) in OFF position, turn on WATER SUPPLIES (2) and check all connections for leaks. Remove AERATOR (3). Operate both HANDLES (1) to flush water lines thoroughly. Replace AERATOR (3). CHECK DRAIN CONNECTIONS Operate POP-UP KNOB (4) and fill lavatory with water. Check that DRAIN STOPPER (5) makes a good seal and retains water in SINK. -
Page 5: Cable Adjustment Procedure
Speed Connect™ Drain Troubleshooting Guide If sink does not hold water even though Stopper is in the “down” position: • Follow CABLE ADJUSTMENT PROCEDURE. If Stopper does not raise up fully or sink drains too slowly: • Follow CABLE ADJUSTMENT PROCEDURE. If you need to remove the Stopper: •... - Page 6 To install the stopper in “Unlocked” mode, insert the Stopper into the Drain so that the Plastic Loop is facing toward the front of the Sink and the American Standard logo is facing rear. Rotate Stopper slightly if necessary so that the Stopper slides all the way down.
- Page 7 M918075-0070A M918504-0070A HANDLE SCREW M918021-0070A ADAPTER M904900-0070A VALVE NUT M913806-0070A BEARING WASHER A954120-0070A VALVE M923058-0070A PUTTY PLATE 065800-0070A ATTACHMENT NUT 066116-YYY0A DRAIN STOPPER 066117-YYY0A M953450-YYY0A 2" FLANGE KIT COMPLETE M962401-YYY0A DRAIN ASSEMBLY LIFT ROD AND KNOB 072574-0070A EXTENSION ROD 066118-0070A PIVOT ROD KIT 070847-0070A CLIP...