24" Built-In Dishwasher w/Integrated Controls (IC)
w/Stainless Tub (ST) Gallery
Front
23
3
/
*Height only adjustable to 35
standard cabinetry cutout. (Dimensions do NOT include insulation –
insulation blanket may be compressed during installation.)
Dishwasher Specifications
•
Product Shipping Weight (approx.) – 91 Lbs.
•
Voltage Rating – 120V / 60 Hz / 15 Amps (maximum 20 Amps if
connected with disposer)
•
Connected Load (kW Rating) @ 120 Volts = 1.44 kW
(For use on adequately wired 120V, dedicated circuit having 2-wire
service with a separate ground wire. Appliance must be grounded
for safe operation.)
•
Amps @ 120V = 15 Amps
Always consult local and national electric & plumbing codes.
•
Meets requirements of ASSE 1006 — integral air gap on supply.
•
Water Pressure – Hot water line to dishwasher must provide
between 20 and 90 pounds per square inch (psi) with at least 120° F
hot water temperature.
Make sure location has correct drain, water and electrical outlets
•
to make connections.
•
Electrical and water supplies should enter cabinet opening on floor,
or through back or side walls, as shown in shaded areas.
•
Keep back free of drain, water & electrical supply.
Connections preferably located toward left side of dishwasher.
•
Do not cross drain, water or electrical lines in front of motor, blower
or frame.
USA
10200 David Taylor Drive
Charlotte, NC 28262
•
•
CANADA
5855 Terry Fox Way
Mississauga, ON L5V 3E4
•
•
FGID2474Q 05/14
"
4
33
/
"
3
4
Adjustable
to 35
/
"
*
3
4
/
" max. when installed in 35
3
4
90°
34"
min. to
35
/
"
3
4
max.
**
24"
min.
3 "
1
/
"
1
4
3
/
" min. to
1
2
2
/
"
1
4
/
" max.
1
4
2
1-800-FRIGIDAIRE
•
•
1-800-265-8352
•
© 2014 Electrolux Home Products, Inc.
(Q Models)
Left
24
1
/
"
4
Door in 90°
open position
27
/
" max.
3
4
90°
Electrical, water,
and drain lines
must be confined
to shaded area
Preferred
drain areas
18"
3 "
3"
**
NOTE: 35
3
/
" max.
4
height for standard
cabinetry cutout.
(
5
/
" min. clearance
16
1"
required from unit to
2
/
"
1
underside of countertop.)
4
24"
•
If connecting drain hose to sink trap, local code may require
installation of Air Gap Kit (not included).
•
Leveling legs supplied to adjust height. (Note: Height only adjustable
to 35-3/4" max. when installed in 35-3/4" max. standard cabinetry
cutout. 5/16" min. clearance required from top of unit to underside
of countertop. Dimensions do NOT inlcude insulation — insulation
blanket may be compressed during installation.)
•
When installing adjacent to wall, cabinet or other obstruction that
extends beyond front edge of unit, allow 2" minimum clearance
between opened door and obstruction.
•
Floor should be flat and free of obstructions with carpet removed
to provide motor clearance.
•
When installing at end of cabinet line, sides and back must be
fully enclosed.
•
Do not install unit under a cooktop, damage will occur.
•
Recommended to seal cabinets, enclosing all sides of dishwasher,
including underside of countertop, with oil-based paint or moisture-
proof polyurethane to prevent possible steam/moisture damage.
Note: For planning purposes only. Refer to Product Installation Guide
on the web at frigidaire.com for detailed instructions.
frigidaire.com
frigidaire.ca
•
Dishwashers
FGID2474Q F / W / B
Right
50
/
"
1
4
22
1
/
"
2
/
"
3
4
Power supply & water inlet location
(bottom rear)
requirements of
24" Built-In
Meets
ASSE 1006
Specifications
subject to change.