LG 32LD650H Setup Manual page 17

Installer Menu Items 073 through 119
Menu
Function
Item
073 CH NOT AVBLE
075 REVERT CH
078 UPN MSB
079 UPN MSB-1
080 UPN MSB-2
081 UPN LSB
082 CHKSM ERROR
083 HANDSHK TIME
084 PERMANENT BLK
087 REAR RGB EN.
088 EN NOISE MUTE
090 KEY LOCK
091 YPrPb2 EN
093 RJP AVAILABLE
094 SAP MENU EN
096 DEF. ASP. RATIO
099 BACK LIGHTING
102 ATSC BAND
103 ATSC TUNE MODE
104 START MINOR CH
106 ASP RATIO LOCK
116 VIDEO MUTE EN
117 FACT DEFAULT
118 POWER SAVINGS
119 DATA CHANNEL
206-4137
Value Range Default Value
0 / 1 0
0 / 1 0
0 ~ 255 0
0 ~ 255 0
0 ~ 255 0
0 ~ 255 0
0 / 1 1
0 ~ 5 5
0 / 1 0
0 / 1 / 17 (LD65xH) 1 (LD65xH)
0 / 2 / 18 (LG710H) 2 (LG710H)
0 / 1 1
0 / 1 0
0 / 1 1
0, 1, 2, 5, 6 0
0 / 1 1
0 ~ 4 2
1 ~ 100, 101 ~
202
200, 201, 202, 255
0 ~ 4 4
0 / 1 1
0 ~ 255 0
0 / 1 0
0 / 1 0
0 / 1 0
1 / 3 / 7 3
0 ~ 135 0
Brief Description of Function and Comments
If set to 1 and Channel Override is 0, "NOT AVAILABLE" message is displayed
when directly accessing a channel not in the favorite Channel List.
If set to 1 and loss of MPI communication occurs, TV tunes to Start Channel.
User programmable number, most significant byte.
User programmable number, most significant byte - 1.
User programmable number, most significant byte - 2.
User programmable number, least significant byte.
Enforces rigid MPI checksum.
Relaxes MPI timing to be compatible with PC-based Windows-
Removes block hours setting for Parental Control and makes block permanent.
Dependent on item 093 RJP AVAILABLE setting. Set to 0 to disable RGB1.
Set to 1 (LD65xH) / 2 (LG710H) to enable for RGB PC. Set to 17 (LD65xH) /
18 (LG710H) for Auto Configure.
If set to 1, audio is muted if no signal is present.
If set to 1, keyboard is locked out, IR is still functional.
Set to 1 to enable HDMI 2 input.
Set to 0 to disable. Set to 1, 2, 5, or 6 for HDMI or DVI Mode. (See
detailed descriptions.)
Set to 0 to disable feature on Function Menu. Set to 1 to enable feature on
Sets default aspect ratio at power up. See detailed descriptions and item 106.
Sets the level of the TV picture back lighting. (See detailed descriptions.)
Set to 1 (default) for Physical Channel scan. Set to 0 for Virtual Channel scan.
Selects Minor Start Channel. Set to 0 for NTSC.
To retain set aspect ratio on power cycle, set to 1. Set to 0 for default ratio on
Set to 0 for Normal. Set to 1 for Blank.
Set to 0 for Normal. Set to 1 to load presets for all Installer Menu settings.
If set to 1, the b-LAN module is always powered. If set to 3, the b-LAN module
is only powered when TV is turned ON. If set to 7, the b-LAN module is never
powered. For LD65xH TVs: If an MPI card is installed, POWER SAVINGS
must be set to 1. (See detailed descriptions.)
Set to 0 to disable. Set to the RF channel number of the Data Channel for
Pro:Centric operation.
Installer Menu (Cont.)
controlled systems.
Function Menu.
Selects ATSC band.
power cycle.
17