Table of Contents
Advertisement
Playback
Blue Back
Set the BLUE BACK mode to AUTO on the MODE-selection
screen.
(See Mode Selection
on page 16.)
This function
eliminates
monitor
noise and mutes sound
during
playback
of unrecorded
portions
of a
-ape, and when receiving
a non-broadcasting
channel.
Blue Back will also appear
if the VCR is set to
-he Auxiliary
input (LINE IN) mode but no video signal is fed to the VCR. (The BLUE BACK mode is set
-0 AUTO at the factory.)
l
Blue
Back does not function
during still
ptcture. variable slow motlor: and vicec search
a
Blue Back
may not function
properly
if the broadcast signal is too strong or to3 \.vesk.
l
Blue Back cannot be recorded.
l
If the antenna
signal IS weak while recording
a TV programme.
or if the input signal IS weak while tape dubbing,
the monitor screen may turn blue back since the unit may not recognize
wpether
or not a proper signai is being
received.
In this event, set the BLUE SCREEN mode to OFF.
hll Auto Playback
This function
only works when AUTO RENTAL mode on the MODE selection
is set to OFF.
311 Auto Playback
lets you enjoy playback
with ease. When you Insert a cassette
with the erasure
Jrotection
tab removed,
your VCR automatically
turns on the power and plays back the tape. When the
ape reaches
its end, the
VCR
automatically
rewinds the tape, ejects it and turns off the power.
l
If the erasure protectlon
hole IS covered,
press the PLAY/x
2 button after the power turns on automatically.
(Only
for VC-H61 OX)
Playback of Hi-Fi Recorded Tapes
This
VCR will play back both video and audio-only
tapes
recorded in the Hi-Fi
mode.
l
Stereo sound
output is only possible
using the AUDfO OUT terminals.
Sound from the radio frequency
converter
(RF OUT) is mono only. A blue screen will appear if audio-only
Hi-Fi tapes are played back.
Audio Output Mode
The audio output mode is controlled by the
AUDIO OUT
button on the remote control. The VCR is nor-
maHy set to the
Hi-Fi
mode, with Q and
q
displayed on the VCR display, and normal stereo sound
3utput.
Select lB, and only the Hi-Fi Left channel audio is heard from both the Right and Left speakers.
Select I& and only the Hi-F; Right channel audio is heard from both the Right and Left speakers.
If you select the mono linear track, B and D wifl disappear.
l
Should the
Hi-Fi output level be poor, the VCR will automatically seiect the mono iinear track output.
l
When playing back tapes which have
only Hi-Fi sound recorded:
if Hi-Fi sound is not reproduced,
or if there is
some noise in the audio, press the CtiANNEL
@I or 0 button until the sound improves.
Adjusting Hi-Fi Audio Tracking
(To
adjust the Hi-Fi tracking manually when playing back a poorly recorded Hi-Fi tape)
l
Normaily you can simultaneously press and hold both CHANNEL @ / 0 buttons to obtain the optimal
I-Ii-Fi audio tracking
I
*If
Hi-Fi
audio is unstable
(frequent
dropouts,
etc.) with a rental video,
a tape recorded
on another
VCR, restore normal tracking while playing back the tape as described below:
@ Simultaneously press the
CHANNEL
@ / 0
buttons.
@
Press the CHANNEL
0
button repeatedly at equal, short intervals until the m and a indicators
disappear from the VCR display.
@ Press the
CHANNEL
@
button in the same manner while counting button operations until the 0
and Gl indicators reappear and then disappear again.
@ Press the
CHANNEL
0
button again for half the number of times counted in step 0
above to
obtain optimal tracking.
21
Advertisement
Table of Contents
