Vantage Hearth VAEDR460VFV User Manual

VARI FOCAL COLOUR DOME CAMERA
USER MANUAL
VAEDR460VFV
FEATURES
The camera use high sensitive colour interline transfer
●
Automatic back-light compensation improves the image quality.
●
Auto-IRIS controlled by electronic system.
●
Automatic White Balance function and Automatic Gain Control function.
●
Manual pan /tilt mechanism, 3-Axis Rotation .
●
Accept 12VDC power supply .
●
ver 1.0
Ⅰ
Lid Lock Clip Used to open or close the
Cover Notch This is the guide mark to attach the
cover to the base .
Tilt locking screw
Using this screw, the slope of the lens can be adjusted
and fixed. normally not needed to adjust.
Base release
Ⅳ
1
Safety Precautions
The installation should be made by qualified service personnel or system
installers and should confirm to all local codes.
1. Power supply
(1) Use with a 12VDCregulated power supply .
(2) To prevent fire or electrical shock, UL listed class 2 wiring should be used
for the 12VDC input terminal.
(3) Be used to connect each lead to the appropriate terminal. Wrong connection
may cause malfunction and/or damage to the camera.
2.Operating and storage locations
(1).Do not attempt to point the camera at the sun or other extremely bright
objects,no matter the camera is power on or not. It leads to damage of the
CCD(Charge Coupled Device).
(2).When camera is installed next to equipment,such as wireless commu-
nication device,it emits a strong electromagnetic field,some irregularity
such as noise on the monitor screen may happen.
(3) .Be sure to use a ceiling board having enough strength to support
this came ra.
1/3" Sony CCD
.
(4).Assemb le the came ra's mai n parts and lens quickly in a clean place.
(5).Do not pull the cable, it may cause disconnection .
(6).Do not touch the inside of camera even if something is wrong.
(7).Before installation,make sure to disconnect the power supply first,
check the ground connection,and then install it.
(8).Operating temperature range:-10℃~+50℃,(14°F~122°F);
Storage temperature range:-20℃~+60℃, (-4°F~140°F).
(9). Be sure to use proper screws to mount the camera firmly.
4 Installation Instructions
1. Unlock the cover using thumb or screwdriver
don't press too hard.
Cover dome. To open the
2. Lift off cover angled as shown, this can be
cover dome, press the locker.
stiff but this is normal.
Push it outward and rotate the
main body in UNLOCK direction
when you want to remove the
Mount bracket from the Main
body or to remove the installed
camera from the Mount bracket.
When you reattach it will click
into place and be re-locked.
Ⅱ
3. Take off inside cover and adjust to suit.
Ⅴ
2
Handling of the unit
(1) Never attempt to disassemble or modify the camera.
(2) If an abnormality should occur, immediately turn off the power and consult
with expert.
3 Parts Description
Dome cover (transparent)
Body cover
Dome base
Inner Cover
Just using one hand can just gently squeeze the cover using thumb
and index finger the inner cover can just be lifted off, to re attach
just push back, and will click into place.
Ⅲ
4. Unlock the base using pressing
the plastic clip.Used as a ceiling
or wall fixture. It is fixed using
three long tab screws provided in
the package, allows fixing of pro-
duct to be done cleanly and not
get dust inside camera.
5. Drill a hole in the
place where the
camera is installed
6. Install base first,
and remove ceiling
mount if required.
Ⅵ
Camera body
Mounting Holes
Mount Bracket
Ceiling
Ceiling mount
opener