Advertisement
e-DATA MEMORY
You can use the watch's e-DATA MEMORY to store
Text
e-mail addresses, Web page URLs, and other text
data. You can store up to 20 records (data items),
and even use a password to limit access to e-DATA
MEMORY contents.
• You can input alphabetic lower-case and upper-
case characters, symbols, and numbers for an e-
DATA MEMORY record.
• You can input up to 20 characters for the text of
each record.
• Records are stored in memory in the sequence
they are created.
Record number
(Page number)
• All of the operations in this section are performed in
the e-DATA MEMORY Mode, which you enter by
pressing C.
To create a new e-DATA MEMORY record
1. In the e-DATA MEMORY Mode, press B and D at
the same time to display the new data screen.
• You do not have to perform the above step if the
new data screen is already on the display.
• The new data screen is the one that is blank
(contains no text).
• Take care that you press B and D at the same
time. Accidentally pressing B alone changes to
the new password setting screen (
old password input screen (
happens, press B again to exit the password
screen, and then carefully press B and D at the
New Data Screen
same time.
• If the message
means that memory is full. To store another
record, you will first have to delete some of the
records stored in memory.
2. Hold down A until the flashing cursor ( ) appears on the display, which
indicates the setting screen.
3. Use D and B to change the character at the cursor position. The character
changes in the sequence shown below.
Press
.
to
(space)
(lower-case)
0 to
(number)
• See the "Character List" at the back of this manual for information about
the characters you can input.
4. When the character you want is at the cursor position, press C to move the
cursor to the right.
• You can move the cursor to the left by pressing L.
5. Repeat steps 3 and 4 until the text is complete.
6. Press A to store your data and return to the e-DATA MEMORY record
screen (without the cursor).
• When the text has more than four characters, it scrolls from right to left on the
display.
To recall e-DATA MEMORY records
In the e-DATA MEMORY Mode, press D to scroll forward through e-DATA
MEMORY records.
• Pressing D while the last record in memory is on the display changes to the
new data screen. Pressing D again displays the first record.
To edit an e-DATA MEMORY record
1. In the e-DATA MEMORY Mode, display the record you want to edit.
2. Hold down A until the flashing cursor appears on the display.
3. Use C and L to move the flashing to the character you want to change.
• Use C to move the cursor to the right, and L to move it to the left.
4. Use D and B to change the character.
5. After making the changes you want, press A to store them and return to the
e-DATA MEMORY record screen.
To delete an e-DATA MEMORY record
1. In the e-DATA MEMORY Mode, display the record you want to delete.
2. Hold down A until the flashing cursor appears on the display.
3. Press B and D at the same time to delete the record.
• The message
appears to indicate that the record is being deleted.
After the record is deleted, the cursor appears on the display, ready for
input.
4. Input data or press A to return to the e-DATA MEMORY record screen.
Using a Password to Protect e-DATA MEMORY Data
You can register a 4-digit password to keep e-DATA MEMORY data secure.
Important!
Use a 4-digit password that is easy for you to remember, but difficult for others
to decipher. If you forget the password, you will have to have your watch
initialized (which deletes all data in memory) in order to access the e-DATA
MEMORY again. To have the watch initialized, contact the store or dealer
where you purchased it, and ask to have the AC operation performed.
USER'S GUIDE 2441
) or the
). If this
appears on the display, it
Press
.
to
(symbol)
to
(upper-case)
To register a new password
1. In the e-DATA MEMORY Mode, press B.
• This displays a screen that shows
Black on white
xxxx, with the first hyphen flashing. This is the
new password setting screen.
2. Press D to scroll through numbers at the first digit.
3. When the first digit is the number you want, press
C to advance to the next digit.
4. Repeat steps 2 and 3 to input all four digits of the
password you want.
• Pressing B while inputting a new password
clears your input and returns to the e-DATA
MEMORY record screen.
5. After all four of the password digits are the way you
want, press C to register them.
• After you register a password, the e-DATA MEMORY record screen appears
with
displayed at the top in red on blue. The red on blue coloring
indicates that e-DATA MEMORY is protected by a password.
• After registering a password, you can input, recall, edit and delete data, if you
want. After you exit the e-DATA MEMORY Mode, you will have to input the
password every time you want to enter it again.
To input the password
1. Enter the e-DATA MEMORY Mode.
2. On the password input screen (
Red on blue
input the password.
• Press D to scroll through numbers at each digit.
• Press C to advance to the next digit.
3. After the password is the way you want, press C.
• The e-DATA MEMORY record screen appears if the
password you input matches the one you
registered.
• The password input screen reappears if the
passwords do not match.
To change the password
1. While a record screen or password input screen is on the display in the e-
DATA MEMORY Mode, press B.
xxxx for input of the current password.
• This displays
2. Input the current password.
• Press D to scroll through numbers at each digit.
• Press C to advance to the next digit.
3. After the password is the way you want, press C.
• If the password you input matches the current password
appears for input of the new password.
• The password input screen appears if the passwords do not match.
4. Input the new password.
• Press D to scroll through numbers at each digit.
• Press C to advance to the next digit.
5. After the new password is the way you want, press C to register it and
change to the e-DATA MEMORY record screen.
input screen is on the display, you can press B
• While the
or
to change to the password input screen.
To delete the password
1. While a record screen or password input screen is on the display in the e-
DATA MEMORY Mode, press B.
• This displays
xxxx for input of the current password.
2. Input the current password.
• Press D to scroll through numbers at each digit.
• Press C to advance to the next digit.
3. After the password is the way you want, press C.
• If the password you input matches the current password,
appears for input of the new password.
• The password input screen appears if the passwords do not match.
xxxx is on the display, hold down A. Keep A depressed
4. While
until
first appears, and then the e-DATA MEMORY record screen
appears.
Alarm
You can set five independent Daily Alarms. When an
Alarm time
alarm is turned on, the alarm tone sounds when the
(Hour : Minutes)
time is reached.
You can also turn on an Hourly Time Signal that
causes the watch to beep twice every hour on the
hour.
• The alarm screen is indicated by the
in the upper display, while
Hourly Time Signal screen.
• The five alarms are identified by alarm numbers
through
1
P-5
• Alarm settings (and Hourly Time Signal settings)
are available in the Alarm Mode, which you enter by
Alarm number
pressing C.
(Page number)
To set an alarm time
1. In the Alarm Mode, use D and B to select the
alarm whose time you want to set.
Press
Alarm 1
Time
Signal
2. After you select an alarm, hold down A until the hour setting of the alarm
time starts to flash, which indicates the setting screen.
• This operation automatically turns on the alarm.
3. Press C to move the flashing between the hour and minutes.
4. While a setting is flashing, use D (+) and B (–) to change it.
• When setting the alarm time using the 12-hour format, take care to set the
time correctly as a.m. (no indicator) or p.m. (P indicator).
5. Press A to exit the setting screen.
xxxx),
xxxx
xxxx
indicator
indicates the
P-
.
.
Press
.
Alarm 2
Alarm 3
Alarm 5
Alarm 4
2
Advertisement
