Advertisement
EI24ID80Q / EI24ID50Q / EI24ID30Q
DISHWASHER
EI24ID50QS
Front
*Height only adjustable to 35
standard cabinetry cutout. (Dimensions do NOT include insulation –
insulation blanket may be compressed during installation.)
Built-In Dishwasher Specifications
Product Weight – 98 Lbs.
•
Voltage Rating – 120V/60Hz/15 Amps
•
Connected Load (kW Rating) @120 Volts = 1.44 kW
•
(For use on adequately wired 120V, dedicated circuit having 2-wire service
with a separate ground wire. Appliance must be grounded for safe operation.)
Amps @ 120V = 15A
•
Always consult local and national electric & plumbing codes.
•
Meets requirements of ASSE 1006 — integral air gap on supply.
Water Pressure – Hot water line to dishwasher must provide between 20 and
•
90 pounds per square inch (psi) with at least 120° F hot water temperature.
Make sure location has correct drain, water and electrical outlets to make
•
connections.
Electrical and water supplies should enter cabinet opening on floor, or
•
through back or side walls, as shown in shaded areas.
Keep back free of drain, water & electrical supply.
•
Connections preferably located toward left side of dishwasher. Do not cross
•
drain, water or electrical lines in front of motor, blower or frame.
Electrolux Major Appliances, N.A.
USA
•
10200 David Taylor Drive
CANADA
•
5855 Terry Fox Way
EI24ID50Q 03/14
23
/
"
3
4
33
/
"
3
4
Adjustable
to 35
/
"
*
3
4
FPO
/
" max. when installed in 35
/
3
3
4
90°
34"
min. to
35
/
"
3
4
**
max.
24"
min.
3 "
1
/
"
1
4
3
/
" min. to
1
2
2
/
"
1
4
1
/
" max.
4
2
•
Charlotte, NC 28262
•
1-877-4electrolux (1-877-435-3287)
•
Mississauga, ON L5V 3E4
•
1-800-265-8352
Left
50
24
/
"
1
4
Door in 90°
open position
27
" max.
4
90°
Electrical, water,
and drain lines
must be confined
to shaded area
Preferred
drain areas
18"
3 "
3"
**
NOTE: 35
/
" max.
3
4
height for standard
cabinetry cutout.
(
/
" min. clearance
5
1"
16
required from unit to
2
/
"
1
underside of countertop.)
4
24"
If connecting drain hose to sink trap, local code may require installation of
•
Air Gap Kit (not included).
Leveling legs supplied to adjust height. (Note: Height only adjustable to
•
35-3/4" max. when installed in 35-3/4" max. standard cabinetry cutout.
5/16" min. clearance required from top of unit to underside of countertop.
Dimensions do NOT include insulation — insulation blanket may be
compressed during installation.)
When installing adjacent to wall, cabinet or other obstruction that extends
•
beyond front edge of unit, allow 2" minimum clearance between opened door
and obstruction.
Floor should be flat and free of obstructions.
•
When installing at end of cabinet line, sides and back must be fully enclosed.
•
Do not install unit under a cooktop, damage will occur.
•
Recommended to seal cabinets, enclosing all sides of dishwasher, including
•
underside of countertop, with oil-based paint or moisture-proof polyurethane
to prevent possible steam/moisture damage.
Note: For planning purposes only. Refer to Product Installation Guide
on the web at electroluxappliances.com for detailed instructions.
•
electroluxappliances.com
•
electroluxappliances.ca
© 2014 Electrolux Home Products, Inc.
Right
/
"
1
4
22
/
"
1
2
/
"
3
4
Power supply & water inlet location
(bottom rear)
Meets
requirements of
ASSE 1006
High standards of quality at Electrolux Home Products, Inc.
mean we are constantly working to improve our products.
We reserve the right to change specifications or
discontinue models without notice.
Advertisement
