Download Print this page

Kenmore 258.33052310 Use & Care Manual

Window fan.
Hide thumbs
   

Advertisement

IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions should always be
taken including the following:
1. Read all instructions before using this appliance.
2. Use fan only for purposes described in the instruction manual.
3. To protect against electrical shock do not immerse unit, plug or cord in
water or spray with liquids and plug the appliance directly into a 120V
AC electrical outlet.
4. Close supervision is necessary when any appliance is used by or near
children.
5. Unplug from outlet when not in use, when moving fan from one location
to another, before putting on or taking off parts and before cleaning.
6. Avoid contact with moving parts.
7. Do not operate in the presence of explosive and/or flammable fumes.
8. To avoid fire hazard, NEVER place the cord under rugs or any parts near
an open flame, cooking or other heating appliance.
9. Do not operate any appliance with a damaged cord or plug after the
appliance malfunctions, or has been dropped/damaged in any manner.
Discard fan or call the following customer assistance number to arrange
for possible product repair: 1-877-777-8065
10. Do not run cord under carpeting. Do not cover cord with throw rugs,
runner, or similar coverings. Do not route cord under furniture or
appliances. Arrange cord away from traffic area and where it will not be
tripped over.
11. The use of attachments not recommended or sold by the appliance
manufacturer may cause hazards.
12. Do not let the cord hang over the edge of a table, counter or come in
contact with hot surfaces or leave exposed to high traffic areas.
13. Do not use outdoors.
14. To disconnect, grip plug and pull from wall outlet. Never yank on cord.
15. Always use on a dry, level surface.
16. Do not operate fan until fully assembled with all parts properly in place.
17. This product is intended for HOUSEHOLD USE ONLY and not for
commercial or industrial applications.
FEATURES / OPERATION
INSTALLATION INSTRUCTIONS
NOTE: Make sure you remove all contents from the package. Check packaging for stored
fan parts before discarding.
The window fan comes fully assembled and is ready for immediate installation.
This window fan has been designed to fit double-hung windows with minimum openings of
25.5 inches (65cm) wide and 8 inches (20cm) high.
Horizontal Window Fan Installation
NOTE: This fan is designed and recommended
Figure 1
Horizontal
for installation in the window so that it is
A
B
C
D
situated behind an existing window screen.
17cm
1. Align the Window Fan horizontally in the
window with the controls facing you and
the power cord located on the bottom of
the window fan.
6cm
G
F
2. Set the fan into your window opening (note
A. Rubber Strip
that in most cases the window screen does
B. Slider Safe
®
Extender Panel
not have to be removed or left open).
C. Fan Blades
3. If the fan does not fit snugly to the left
D. Locking Tab
and right of the window casing, open the
E. Adjustable Extruded Gasket
Locking Tab (D) by pulling up and pulling
F. Built-in Extender Panel
out the Built-In Extender Panel (F) until the
G. Control Panel
fan sits safely in your window. Re-lock or
close the locking tab after the fan is safely
secured in the window.
A
4. If the fan still does not fit snugly attach the
Slider Safe
Extender Panel located in the
®
polyfoam packaging in the original box.
Slide out the Rubber Strip (A) from the left
side of the fan - see Figure 2. Then slide the
Slider Safe
®
Extender Panel along the left
side of your Window Fan. Slide the Slider
A
Safe
®
Extender Panel completely down
B
the tab until it is flush on both the top and
bottom of the Window Fan. Replace with
the Rubber Cover by sliding down along the
left side of the added Slider Safe
®
Extender
Panel - see Figure 3.
5. To keep the fan in place, carefully close the window so that the bottom edge of the
window rests on the flat area on the top of the fan.
Vertical Window Fan Installation
1. For vertical orientation, install unit using rigid extender panels at the base of window.
2. Set the Fan vertically in your window opening with the left side of the fan situated on the
bottom and the Built-In Extender Panel on top.
KWF0522E_12ESM1.indd 1
IMPORTANT SAFEGUARDS
18. WARNING: To reduce the risk of fire or electric shock, do not use this fan
with any solid-state speed control device.
19. This product employs overload protection (fuse). A blown fuse indicates
an overload or short-circuit situation. If the fuse blows, unplug the product
from the outlet. Replace the fuse as per the user servicing instructions
(follow product marking for proper fuse rating) and check the product.
If the replacement fuse blows, a short circuit may be present and the
product should be discarded or call the following customer assistance
number to arrange for possible product repair: 1-877-777-8065
20. Do not use an extension cord with this fan.
21. For general ventilating use only. Do not use to exhaust hazardous or
explosive materials and vapors.
PLEASE READ AND SAVE THESE
IMPORTANT SAFETY INSTRUCTIONS
THIS APPLIANCE HAS A POLARIZED PLUG (one blade is wider
than the other). To reduce the risk of electric shock, this plug is
intended to fit in a polarized outlet only one way. If the plug
does not fit fully in the outlet, reverse the plug. If it still does not
fit, contact a qualified electrician to install the proper outlet.
DO NOT ATTEMPT TO MODIFY THIS PLUG OR DEFEAT THIS
SAFETY FEATURE IN ANY WAY.
FEATURES / OPERATION
3. Set the fan into your window opening (note that in most cases the window screen does
not have to be removed or left open).
4. If the fan does not fit snugly to the top and bottom of the window casing, attach the
Slider Safe
Extender Panel and adjust the built-in extender screen until the fan fits
®
securely in your window.
NOTE: Be sure fan is securely installed in your window at all times. Do not lean or push on
the fan while it is in the window.
OPERATING INSTRUCTIONS
Vertical
• Plug the fan into a 120V AC electrical outlet.
• To start the unit and run continuously, push the Power Button ( ) once for the Low setting
(Lo) and press the button twice for the Medium setting (Med), a third press of the button
will switch to High setting (Hi).
• To stop the unit, press and hold the Power Button ( ) for two seconds or you can manually
cycle through all of the speeds until all of the LED indicators are no longer lit.
E
COMFORT CONTROL THERMOSTAT INSTRUCTIONS
Your fan is equipped with a technologically advanced electronic
thermostat. This feature will automatically turn the fan "ON" or "OFF"
depending on the preset comfort level. The comfort level ranges
between 60° and 80° Fahrenheit.
To take advantage of the electronic thermostat, continue to press the
Power Button ( ) until the desired temperature is reached. The selected
temperature indicator light and either Lo or Med or Hi indicator light
will illuminate. When room temperature drops below the set
temperature, the fan will stop. When the room temperature rises above
Figure 2
the set point, the fan will turn on automatically.
F E
For example, if you set your thermostat to 75 degrees then your fan will
run until the set temperature is reached. Once the temperature rises
above the set temperature the fan will automatically turn on again.
NOTE: The electronic thermostat has memory. The thermostat will remember the previous
temperature setting after the unit has been turned off. However, if the unit is unplugged,
Figure 3
the thermostat will be reset and will no longer remember the previous temperature setting.
F E
KENMORE ONE YEAR LIMITED WARRANTY
If this product fails due to a defect in material or workmanship within
one year from the date of purchase, return it with proof of purchase to
any Sears store or other Kenmore outlet in the United States for free
replacement.
This warranty is void if this product is ever used for other than private
household purposes.
This warranty gives you specific legal rights, and you may also have other
rights which vary from state to state.
Sears Brands Management Corporation, Hoffman Estates, IL 60179
KENMORE GARANTÍA LÍMITADA DE UN AÑO
Si este producto falla debido a un defecto en material o a la ejecución
en el plazo de un año a partire de la fecha de la compra, deveulvalo con
comprobante de compra a cualquier tienda Sears o un otro Kenmore outlet
en los Estados Unidos para el reemplazo gratis.
Esta guarantía es invalido si este producto se utiliza para con excepción de
los propósitos privados de casa.
Esta guarantía le da los derechos legales especificos, y usted puede
también tener otros derechos que varían de estado a estado.
Sears Brands Management Corporation, Hoffman Estates, IL 60179
CLEANING / MAINTENANCE
CLEANING AND MAINTENANCE INSTRUCTIONS
Follow these instructions to correctly and safely care for your window fan. Please remember:
REPLACEABLE FUSE
If your (5 Amp, 125 Volt) replaceable fuse blows, please order a new fuse at
1-877-777-8065. Follow the below instructions to replace the fuse on the plug.
User Servicing Instructions
1. Unplug your fan. Grasp plug and remove from the receptacle or other outlet device. Do
not unplug by pulling on cord.
2. Open fuse cover, located on the top of the plug, by using your thumb or a flathead
screwdriver to slide the cover down towards the prongs.
NOTE: Ensure that fuse cover is completely open before
Figure 4
attempting to remove fuse.
3. Remove fuse carefully by using a small screwdriver to pry the
Fuse
fuse out of the compartment by the metal ends of the fuse.
Fuse cover
(see Figure 4)
4. Place plug on a solid, flat surface. Insert new 5 Amp, 125 Volt
fuse into fuse compartment and use a small screwdriver to
secure the metal ends of the fuse into the compartment.
CAUTION: Risk of fire. Replace fuse only with 5 Amp, 125
Volt fuse.
5. Slide fuse cover closed completely. If fuse cover is difficult to close, make sure fuse is
secured in place completely by pressing down on metal ends of the fuse.
6. Risk of fire. Do not replace attachment plug. It contains a safety device (fuse) that should
not be removed. Discard product if the attachment plug is damaged.
FAN CLEANING
• Always unplug the fan before cleaning or disassembling.
• Do not allow water to drip on or enter into the fan motor housing.
• Be sure to use a soft cloth moistened with mild soap solution.
• Do not use gasoline, thinner or benzene as a cleaner.
• The fan grills not supposed to be disassembled by user. Recommend to use a small paint
brush and a vacuum to clean the fan blades.
Fan Blade and Front Grill Cleaning
1. Using a Phillips head screwdriver, remove the screws located around the perimeter of the
rear grill. Carefully separate the front and the rear grills from the end opposite the built
in extenders. Do not completely detach the grills as this may damage the extender clips.
Separate only enough to gain access to the blades with one hand.
2. Clean blades and grills with a soft, moist cloth (see above).
3. Securely fasten the grills together.
FAN STORAGE
For all window fans, and fans that come already assembled:
• It is important to keep it in a safe, dry location.
• We recommend using the original (or appropriately sized) box.
• Please remember to protect the fan from dust or moisture.
Use & Care Guide
Manual de Uso y Cuidado
English/Español
Kenmore
®
Window Fan
Ventilador de Ventana
Model/Modelo: 258.33052310
Customer Assistance / asistencia al cliente:
1-877-777-8065
Sears Brands Management Corporation,
Hoffman Estates, IL 60179
www.kenmore.com
www.sears.com
www.kmart.com
P/N 163506
CLEANING / MAINTENANCE
WINDOW FAN ACCESSORIES
Window Fan
Extender Panel
(164241)
Rubber Strip
(164243)
Adjustable
Extruded Gasket
(164242)
Metal ends
USE & CARE ASSISTANCE
If you have safety, operation or maintenance questions concerning the use of this product,
call the following customer assistance number: 1-877-777-8065 and reference KWF0522E
To order, visit the web site
www.kenmore.com or call
1-877-777-8065
12/11/12 8:43 AM

Advertisement

   Related Manuals for Kenmore 258.33052310

   Summary of Contents for Kenmore 258.33052310

  • Page 1

    When using electrical appliances, basic safety precautions should always be 18. WARNING: To reduce the risk of fire or electric shock, do not use this fan any Sears store or other Kenmore outlet in the United States for free English/Español taken including the following: with any solid-state speed control device.

  • Page 2

    NOTA: asegúrese que la cubierta del fusible esté Para realizar un pedido, Banda de hule Fusible completamente abierta antes de intentar retirar el fusible. visite www.kenmore.com o Cubierta (164243) 3. Retire el fusible con cuidado utilizando un destornillador llame a 1-877-777-8065 del fusible pequeño para hacer palanca en los extremos metálicos del...

Comments to this Manuals

Symbols: 0
Latest comments: