Advertisement
Quick Links
S
PECIFICATIONS
Nominal Input Level
Input Impedance
Output Impedance
Frequency Response
+0 / -3 dB
Tone Controls
Bass
Treble
Bright
Midrange
Frequency Range
Q
Edge
Boost Control
Gain
Drive Control
Gain
Gain Type
Low End Compensation
Balanced Output
Impedance
Nominal Level
Frequency Response
XLR Connections
Options
Phones
Impedance
Power Requirements
Powering Modes
Dimensions
Weight
Specifications are subject to change without notice!
EBS MicroBassII
M
S
B
ADE IN
WEDEN
F
12, SE-171 66 S
RAMNÄSBACKEN
+46-8-735 00 10, F
E-M
: ebs.sweden@bass.se
AIL
W
: http://www.ebs.bass.se
EB
November 2003
- 8 dBv
10 Mohms (Ch A), 1 Mohms (Ch B)
10 kohms
20 – 20 kHz
+/- 15 dB @ 100 Hz
+/- 15 dB @ 10 kHz shelving
+ 12 dB @ 10 kHz,15dB gain
+/- 12 dB
50 –2.000 Hz
0.80
+/- 12 dB @ 7 kHz
0 – 30 dB
0 – 35 dB
Class A Tube Emulator
< 250 Hz
500 ohms balanced
-10 dBv
+0/-3 dB 20 Hz – 30 kHz
1-GND, 2-Hot, 3-Cold
GND Lift, Speaker Simulator
3 – 200 ohms recommended
9 V DC Regulated, 10 mA
15 mA with Phones
DC Power Supply, Battery,
48V Phantom power,
EBS Phantom Power System
6.0" (153 mm) Width,
4.3" (110 mm) Height,
2.3" (58 mm) Depth
875 g (1.95 lb.)
EBS S
AB
Y
WEDEN
, S
OLNA
WEDEN
: +46-8-735 00 15
AX
U
M
SERS
B
L
LACK
ABEL
EBS M
ICRO
EBS Professional Bass Equipment
ANUAL
S
ERIES
B
II
ASS
Advertisement
Related Manuals for EBS MicroBassII
Summary of Contents for EBS MicroBassII
- Page 1 Power Requirements 9 V DC Regulated, 10 mA 15 mA with Phones Powering Modes DC Power Supply, Battery, 48V Phantom power, EBS Phantom Power System Dimensions 6.0” (153 mm) Width, 4.3” (110 mm) Height, 2.3” (58 mm) Depth Weight 875 g (1.95 lb.)
-
Page 2: Table Of Contents
LOCK IAGRAM ONTENTS ETTING TARTED IRECT NJECTION SING NSTRUMENT SING NSTRUMENTS EHEARSAL REAMP OOD TO ONTROLS AND UNCTIONS HANNEL • B NPUT OOST • T REBLE • E RIGHT NHANCED ILTER HANNEL • E IDDLE • M RIVE WITCH OMMON EATURES •... -
Page 3: Getting Started
When using the phantom power, you need to connect a stereo ¼” cable between the OUTPUT from the EBS- GOOD LUCK! MicroBassII and the input jack of the amplifier, or if option is available on the amp, to the effect return jack. Please refer to ____________________________________________________ the amps user manual on how to engage this on the amp. -
Page 4: Using One Instrument
HEADPHONES – The headphones output enables you to use the for overdriven sounds and lead playing. Both LED’s will now MicroBassII as a rehearsal amp, or to play without a poweramp/speaker light. cabinet configuration. When using the headphones you should not use the 48V phantom power option due to the high power consumption. -
Page 5: Using Two Instruments
B. Normally you would connect the instrument with lowest output to channel A. EFFECTS LOOP – EBS MicroBassII is provided with an effect loop for the use of external units such as box or rack effects. 2) Connect the Output to power amplifier or amplifier head. -
Page 6: Rehearsal Preamp
• M ETTING TARTED RIVE WITCH DRIVE – The DRIVE knob controls the amount of gain in the tube EHEARSAL REAMP emulation stage, and provides extra gain all the way up to 30 dB. When pushing this control to distortion, a tube like limitation is achieved 1) Connect your instrument to input A. -
Page 7: Good To Know
For normal operation, try to keep the Volume as high as possible. __________________________________________________________ For best results, always gain up the MicroBassII from the Boost and the Drive controls in minimum position. EDGE FILTER – The EDGE filter is a 'bell' type filter peaking at... -
Page 8: Input • Boost
__________________________________________________________ BOOST - Control to adjust the instruments' signal strength to the right operating level in the EBS MicroBassII. This control goes from unity gain ENHANCED FILTER MODE – The enhanced mode switch allows the all the way up to 30dB with low noise. For best results, always try to gain Treble control to have effect on the midrange in this filter.