Table of Contents
Advertisement
STEP 2
TECHNICAL DETAILS
WF645,WF640,
Models
WF630,
and WF620
59.5cm wide
Dimensions
85cm high
60cm deep
Capacity
from 1 to 6kg
Electric
voltage 220/230 Volts 50Hz
Connections
maximum absorbed power 1700W
Spin Speed
up to 1400rpm - WF645 & WF640
up to 1300rpm - WF630
up to 1200rpm - WF620
Control
programmes
programme D
according to
temperature 60˚C
IEC456
run with a 6kg load
directive
4
LEVEL?...
YOUR MACHINE WILL BE NOISY IF THE TWO FRONT FEET ARE NOT
ADJUSTED SO THE MACHINE STANDS FIRM AND LEVEL.
The inclination of the machine, measured on the top, must not exceed 2˚.
- Move your machine into final location.
Take care not to trap or kink the hoses.
- Turn one or both front feet clockwise until
the machine stands firm and level.
The spring on each foot will stop them
coming loose.
If it is placed on a fitted carpet, adjust the feet
to ensure that there is adequate ventilation
beneath the washing machine.
1
REMOVE TWO TRANSIT FIXINGS...
IMPORTANT:
Situated, one either
side of the rear panel,
both transit bolts
(complete with
spacers) MUST be
removed before use...
Use a crosshead
Failure to do so may
screwdriver to
cause damage to
remove the
plastic cover.
your machine!
3
DRAINAGE SYSTEM... we recommend one of the following:
STANDPIPE METHOD
NOTE: ALTHOUGH YOU MAY NEED TO
Hooked End Support
MOVE THE HOOKED END SUPPORT
ALONG THE GREY DRAINAGE HOSE,
DO NOT REMOVE IT.
WHICHEVER DRAINAGE METHOD
YOU USE, MAKE SURE THAT THE
HOOKED END SUPPORT IS FIXED
LEVEL TO, OR ABOVE THE 'PLUMBING
INDICATOR LINE'*
(*see Getting to Know your Appliance)
5
PLUG YOUR MACHINE INTO AN ELECTRICAL SOCKET WHICH IS
EASILY ACCESSIBLE. SWITCH ON
Installation
Follow these instructions to remove the TWO transit fixings.
Unscrew the
STOP when 3
Hold, slide
bolt using a
threads can be
across and pull
13mm spanner.
seen.
to remove.
UNDER SINK METHOD
Insert drainage hose
approximately 100mm
into the standpipe.
OR
.............................
Standpipe height:
cut off the blocked
minimum 500mm
from the floor.
end of the under sink
drainage unit.
CONNECT TO THE POWER SUPPLY...
NOTE: Hotpoint recommend extension
leads are not used.
NOTE: The mains cable must only be
replaced by an authorised serviceman.
2
It is important the transit
PLEASE USE THE NEW HOSES SUPPLIED, FITTED
bolt and spacer come out
TO THE MACHINE.
intact (see pic).
For safety, replace both
plastic covers over the
DO NOT REMOVE!
holes left by removing
Check both hot
i
the two bolts.
and cold water
supplies are
running freely...
Check the hoses
iii
at least once a
year. Replace any
that show signs of
cracking, they
might burst due
to water pressure.
800mm
from floor
If you have no hot water supply...
A cold fill adaptor is available from
Fix the hooked
Attach the GREY
your local Hotpoint authorised
Service Centre or by calling the
end support at
drainage hose to the
Genuine Parts & Accessories Hotline
a minimum
under sink drainage
(see KEY CONTACTS).
800mm from
unit securely, using a
the floor.
hose clip.
6
READY...
TO CHECK ALL PARTS OF THE INSTALLATION AND TO THOROUGHLY
CLEAN THE INSIDE OF YOUR MACHINE:
RUN PROGRAMME 'B' (refer to 'Programme Selection', STEP 4).
✗
WITHOUT ANY LAUNDRY
and
WITHOUT ANY DETERGENT
THIS WILL TAKE APPROXIMATELY 2hours 20minutes TO COMPLETE
CONNECT TO THE WATER
SUPPLY...
Old hoses may
cause leaks due to
worn out washers
or may split due to
water pressure.
Connect fill hoses to the
ii
water supply taps:
Red or Grey Hose end to
Hot and Blue Hose end
to Cold.
TURN BOTH TAPS ON...
iv
Water pressure at the tap
must be in the range...
Max. 1Mpa (10 bar) and
Min. 0.05Mpa (0.5 bar)
✗
Hide quick links:
Advertisement
Table of Contents
