Transcend 128MB–4GB JetFlash User Manual
Transcend 128MB–4GB JetFlash User Manual

Transcend 128MB–4GB JetFlash User Manual

128mb–4gb jetflash

Advertisement

Quick Links

128MB–4GB JetFlash™
User's Manual
P/N TS128M-4GJF110

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 128MB–4GB JetFlash and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Transcend 128MB–4GB JetFlash

  • Page 1 128MB–4GB JetFlash™ User’s Manual P/N TS128M-4GJF110...
  • Page 2: Table Of Contents

    Table of Contents Introduction Package Contents......................1 Features..........................1 System Requirements .......................1 Driver Installation Driver Installation for Windows 98SE ................2 Driver Installation for Windows Me, 2000, and XP ............2 Driver Installation for Mac OS 9.0 or Later ..............2 Driver Installation for Linux Kernel 2.4 or Later ..............2 Partition &...
  • Page 3: Package Contents

    Introduction Thank you very much for purchasing Transcend’s JetFlash™. This small device is designed to expedite the exchange of huge amounts of data between any desktop or notebook computer with a USB port. With a higher storage capacity and a much faster data transfer rates than other typical portable storage media, JetFlash can easily replace floppy diskettes and hard disks.
  • Page 4: Driver Installation

    Driver Installation Driver Installation for Windows 98SE 1. Put the Driver CD into the CD-ROM drive (Auto-Run supported). Select the Win98 Driver button. 2. Follow the on-screen instructions to complete the driver installation. 3. Plug your JetFlash into an available USB port. A new Removable Disk drive with a newly assigned drive letter will appear in the My Computer window.
  • Page 5: Partition & Security Function

    Partition & Security Function Partition Types You can partition JetFlash into two partition types. The two types are: Type 1: “Public Area Only” This is the default partition type for JetFlash. It allows the entire volume of JetFlash memory to be accessed by anyone.
  • Page 6 3. The following window will appear. Select Yes to continue or No to stop. 4. Select the partition type you need. a. To partition your JetFlash to the default type, i.e.,“Public Area Only.” Choose the Public Area Only, and then select OK. b.
  • Page 7: Access Data In The Security Area

    5. The following window will appear to warn you. Select OK to continue or Cancel to stop. 6. Once the partition is finished, the following window will appear. Select OK. Access Data in the Security Area 1. Plug in your JetFlash and double-click the JF-Utility.EXE in JetFlash. The icon will appear in the system tray and the following JF-Utility window will appear.
  • Page 8: Log Out Of Security Area

    3. The following window will appear. Enter the correct password and select OK. If a Password Hint was set up during the partition procedure, you can select the Hint button to display your Password Hint to help you to remember the password. 4.
  • Page 9 2. The following window will appear. Select the Manage Password button. 3. Input the Old Password, and N Password and the Confirm New Password in each field. (Maximum size for a password is 8 characters) You can also input a Password Hint to set up a reminder for your new password.
  • Page 10: If You Forget The Password

    If You Forget the Password If you forget your password, you can use the password hint to remember it. If you cannot recall the password using the password hint, then all you can do is run the Partition function again to repartition your JetFlash.
  • Page 11: Lock Your Computer

    4. Select the OK button to enable the PC-Lock function. If you want to lock your computer after shutdown, you can select OK & ShutDown. You can remove your JetFlash when the computer is turned off. 5. The following message will appear to show that the PC-Lock function is enabled. Lock Your Computer After the PC-Lock function is enabled, your computer will be locked whenever you remove your JetFlash.
  • Page 12: System Requirements For Boot-Up Function

    If choosing to use the Boot-Up function, please be aware that there is a maximum capacity size of 500MB (or less) apportioned to the Boot-Up disk sector; this applies to both the USB-ZIP and USB-HDD formats. System Requirements for the Boot-Up Function •...
  • Page 13: Boot-Up Function For Windows Xp

    USB-HDD boot-up type is not supported in Windows Me. 4. The following message will appear. Select OK to continue or Cancel to exit. 5. The following window will appear. JetFlash is now ready for use as an MS-DOS Boot Disk. Select OK to close the window.
  • Page 14 3. Select OK. 4. Select OK to complete the format. 5. Select the Boot-Up button in the JF-Utility window. 6. The following window will appear. Select Yes to continue or No to stop.
  • Page 15: Recovery Function

    7. The Create Boot Disk window will appear. Select the Create Boot Disk button. The USB-HDD boot-up type is not supported in Windows XP. 8. The following message will appear. Select OK to continue or Cancel to exit. 9. The following window will appear. JetFlash is now ready for use as an MS-DOS Boot Disk. Select OK to close the window.
  • Page 16 1. Put the Driver CD into the CD-ROM drive (Auto-Run supported). Plug your JetFlash into an available USB port, and select the Recovery button. 2. The following window will appear. Select OK to continue. 3. The following window will appear. Select OK to continue or Cancel to stop. The Recovery program will perform a low-level format on your JetFlash, erasing all of the data and returning JetFlash to the default configuration.
  • Page 17: Remove Jf-Utility

    Remove JF-Utility When the JF-Utility.EXE file is executed, the icon remains in the system tray. If you do not want to use this JF-Utility anymore, right click the icon and select exit to remove the JF-Utility. Safely Remove Your JetFlash Remove JetFlash in Windows 98SE Unplug JetFlash from your system directly when data is not transferring.
  • Page 18: Troubleshooting

    Troubleshooting If an error occurs, first check the points listed below before taking your JetFlash for repair. If you are unable to remedy a problem from the following hints, please consult your dealer or service center. Driver CD cannot auto-run in Windows Enter Device Manager in the Control Panel and enable the Auto-Insert function for the CD-ROM drive.
  • Page 19 Re-copy the file and refer to the ”Safely Remove Your JetFlash” section to remove the JetFlash after the copy process is completed. File that was just deleted still appears Re-delete the file and refer to the ”Safely Remove Your JetFlash” section to remove the JetFlash after the delete process is completed.
  • Page 20: Specifications

    Size: 64mm x 21mm x 10mm Weight: 11 g Data Retention: Up to 10 years > 100,000 times Erase Cycles: Certificates: CE, FCC, BSMI Ordering Information Transcend P/N Memory Size Features TS128MJF110 128MB Gold TS256MJF110 256MB Green TS512MJF110 512MB Blue...

Table of Contents