Advertisement
Quick Links
W idespread Lavatory Faucet with the
Speed Connect™ Drain
Congratulations on purchasing your American Standard faucet with
the Speed Connect Drain, a feature found only on
American Standard faucets.
Speed Connect Drain*
• 1/3 of the parts, installs in 1/3 of the time
• No tools needed
• Never needs adjustment
• Guaranteed to seal properly the first time, every time.
*Your new American Standard faucet is designed to work only with the Speed Connect drain. Helpful tips for
removing your current drain can be found in the Troubleshooting section of these instructions.
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
Recommended tools
Screwdriver
1
INSTALL SPOUT
Insert SPOUT (1) and CABLE CONNECTOR (2) through center hole, making sure
the SEAL WASHER (3) is properly seated in SPOUT (1).
Assemble RUBBER WASHER (4), BRASS WASHER (5) and LOCKNUT (6) onto SPOUT
SHANK (7) from under side of sink . Make sure SPOUT (1) is centered in the mounting
hole and the slot in the BRASS WASHER (5) faces toward the rear of the sink.
Tighten LOCKNUT (6) firmly. Fig. A.
1A
INSTALL VALVE BODY
Place RUBBER RING (9) into ESCUTCHEON (10).
Install LOCKNUT (11) onto VALVE BODY (12).
From under side of mounting surface, install VALVE BODY (12) through valve
mounting holes. Threads of VALVE BODY (12) should extent at least 5/16
of a inch above mounting surface top. Fig. B.
Important: Thread ESCUTCHEON (10) onto VALVE BODY (12) until snug against
internal stop. This is key to the installation. If not done, the faucet handles won't
work correctly. If necessary, adjust LOCKNUT (11).
Hand tighten LOCKNUT (11) to secure VALVE BODY (12).
Repeat above steps for opposite VALVE BODY (12A).
10
9
5/16'' MIN.
Fig. B.
T M
Channel Locks
Turn off water at
CAUTION
main supply.
10
9
MOUNTING
SURFACE
11
12
12
11
Installation
Instructions
2808.222
2908.222
Tubing Cutter
Adjustable Wrench
1
1
Certified to comply with ANSI A112.18.1
U S 6 0 3 8 5 R e v. 1 . 2
Fig. A.
3
7
SLOT
12a
2808 SERIES
1
4
5
6
2
Advertisement
Related Manuals for American Standard Williamsburg 2808.222
Summary of Contents for American Standard Williamsburg 2808.222
- Page 1 • Guaranteed to seal properly the first time, every time. *Your new American Standard faucet is designed to work only with the Speed Connect drain. Helpful tips for removing your current drain can be found in the Troubleshooting section of these instructions.
- Page 2 INSTALL POP-UP DRAIN Remove CLEAR PLASTIC COVER (1). Remove CARDBOARD SPACER (2) from Fig. A. under DRAIN POP-UP (3). Drop DRAIN BODY (4) through sink drain hole. Make sure WHITE FOAM GASKET (5) is under flange of DRAIN BODY (4). Note: No plumber’s putty or caulk is required.
- Page 3 ATTACH CABLE CONNECTOR Thread CABLE CONNECTOR (1) clockwise onto DRAIN BODY CONNECTION (2) and hand tighten. Fig. A. Your new POP-UP DRAIN installation is now complete. Fig. B. Note: Tailpeice on pop-up drain is 1-1/4” O.D. Fig. B. CHECK OPERATION OF POP-UP Operate LIFT KNOB (1) to verify that STOPPER (2) opens and closes.
- Page 4 INSTALL HANDLES Push ADAPTER (1) on VALVE STEM (2), so that the hole of the ADAPTER (1) without spline is facing up. Thread HANDLE BASE (3) onto VALVE ESCUTCHEON (7) Push LEVER BALL (4) onto ADAPTER (1). Find correct position of HANDLE (4) by adjusting male teeth on ADAPTER (1) to female teeth in...