Plug & Play (Initial Setup); If You Want To Rerun Plug & Play... - Samsung 6000 Series User Manual

Plug & Play (Initial Setup)
When you turn the TV on for the first time, a sequence of on-screen prompts will assist in configuring basic settings. To turn on
the TV, press the POWERC) button.
~
Plug & Play is available only when the Source is set to TV.
~
To return to the previous step in the Plug
&
Play sequence, select Previous, and then press ENTERG'.
~
Before turning on the TV, make you have connected the TV to an antenna or cable connection (Page 8).
Press the
~
or
~
button to select a language. Press ENTER G' twice
when done.
Dettln(}U!)tl'le~~et\Nor'\<;'
Set up your network connection. Press the ENTER G' button to start.
If you do not know your network set up information or want to set to it
later, select
Skip.
We suggest you skip network connection setup now
and refer to "Network menu" in the e-Manual for set up requirements and
instructions, and the Network Connection section of this manual (Page 15).
You can set up the network connection later using the Network menu.
Press the ~ or ~ button to select
Home Use,
and then press the
ENTER G'
button twice.
Select the
Home Use
mode.
Store Demo
mode is for retail environments.
Press the
~
or
~
button to select Auto or Manual, and then press ENTER G' twice.
~
If you selected Auto, you'll go to the Time Zone and DST screen. Select Time
Zone or DST, and then press ENTERG'. On the Time Zone screen, use the
~
or
~
button to select your zone, and then press
ENTER
G'.
On the
DST
screen, press,
ENTERG',
then select whether to turn
DST
(Daylight Savings Time) on or off. When
done, press ENTER G.
~
If you selected Manual, you'll go to the Date and Time screen. Select Date or Time,
and then press ENTERG. Then, use the number buttons or the
~
or
~
button to
set the date or time. Use the .... or ~ button to move between entry fields. When
done setting the
Date
and
Time,
select
Next,
and then press
ENTERG.
Press the
~
or
~
button to select Air or Cable, and then press ENTER G. A check
appears on your selection. Select Next, and then press the ENTER G button. You can
check both if you have both connected.
~
If you selected Cable, you'll go to the Cable System screen. Use the
~
or
~
button to select
Digital or Analog,
and then press.
ENTER
G. Use the ~ or ~
button to select the correct cable signal format -
STD, HRC, or IRC -
and then press
ENTER G. Most cable systems use STD. Select the correct cable signal format for
both the
Digital
and
Analog
systems.
~
When done, select Next, and the press ENTERG.
The channel search will start automatically. This can take up to 30 minutes.
For more information, refer to
Channel
-+
Auto Program
in the e-Manual.
~
Press the
ENTERG
button at any time to interrupt the memorization process.
If you want to watch a broadcast program, select
Close.
If you want to enjoy
Smart Hub,
select
Smart Hub. Smart Hub
will start. For more detailed
information, refer to "Smart Hub" in the e-Manual.
If You Want to Rerun Plug & Play...
[SJ
MENU
-+
System
-+
Plug & Play
-+
ENTER G
~NOTE
• To change the TV's setting from
Store Demo to Home Use
when not in Plug & Play, press the volume button on the TV.
When you see the volume in the OSD, press and hold
MENU
for 5 sec.
Plug & Play (Initial Setup)
When you turn the TV on for the first time, a sequence of on-screen prompts will assist in configuring basic settings. To turn on
the TV, press the POWERC) button.
~
Plug & Play is available only when the Source is set to TV.
~
To return to the previous step in the Plug
&
Play sequence, select Previous, and then press ENTERG'.
~
Before turning on the TV, make you have connected the TV to an antenna or cable connection (Page 8).
Press the
~
or
~
button to select a language. Press ENTER G' twice
when done.
Dettln(}U!)tl'le~~et\Nor'\<;'
Set up your network connection. Press the ENTER G' button to start.
If you do not know your network set up information or want to set to it
later, select
Skip.
We suggest you skip network connection setup now
and refer to "Network menu" in the e-Manual for set up requirements and
instructions, and the Network Connection section of this manual (Page 15).
You can set up the network connection later using the Network menu.
Press the ~ or ~ button to select
Home Use,
and then press the
ENTER G'
button twice.
Select the
Home Use
mode.
Store Demo
mode is for retail environments.
Press the
~
or
~
button to select Auto or Manual, and then press ENTER G' twice.
~
If you selected Auto, you'll go to the Time Zone and DST screen. Select Time
Zone or DST, and then press ENTERG'. On the Time Zone screen, use the
~
or
~
button to select your zone, and then press
ENTER
G'.
On the
DST
screen, press,
ENTERG',
then select whether to turn
DST
(Daylight Savings Time) on or off. When
done, press ENTER G.
~
If you selected Manual, you'll go to the Date and Time screen. Select Date or Time,
and then press ENTERG. Then, use the number buttons or the
~
or
~
button to
set the date or time. Use the .... or ~ button to move between entry fields. When
done setting the
Date
and
Time,
select
Next,
and then press
ENTERG.
Press the
~
or
~
button to select Air or Cable, and then press ENTER G. A check
appears on your selection. Select Next, and then press the ENTER G button. You can
check both if you have both connected.
~
If you selected Cable, you'll go to the Cable System screen. Use the
~
or
~
button to select
Digital or Analog,
and then press.
ENTER
G. Use the ~ or ~
button to select the correct cable signal format -
STD, HRC, or IRC -
and then press
ENTER G. Most cable systems use STD. Select the correct cable signal format for
both the
Digital
and
Analog
systems.
~
When done, select Next, and the press ENTERG.
The channel search will start automatically. This can take up to 30 minutes.
For more information, refer to
Channel
-+
Auto Program
in the e-Manual.
~
Press the
ENTERG
button at any time to interrupt the memorization process.
If you want to watch a broadcast program, select
Close.
If you want to enjoy
Smart Hub,
select
Smart Hub. Smart Hub
will start. For more detailed
information, refer to "Smart Hub" in the e-Manual.
If You Want to Rerun Plug & Play...
[SJ
MENU
-+
System
-+
Plug & Play
-+
ENTER G
~NOTE
• To change the TV's setting from
Store Demo to Home Use
when not in Plug & Play, press the volume button on the TV.
When you see the volume in the OSD, press and hold
MENU
for 5 sec.