Samsung 8000 Series User Manual page 10

When you turn the TV on for the first time, a sequence of on-screen prompts will assist in configuring basic settings. To turn on
the TV, press the POWER3 button.
✎
Plug & Play is available only when the Source is set to TV.
✎
To return to the previous step in the Plug & Play sequence, press the red button, and then press ENTER(.
✎
Before turning on the TV, make sure you have connected the TV to an antenna or cable connection (p. 8).
1
Selecting the OSD
Language
2
Setting up the Network
3
Software Upgrade
4 Selecting the usage
mode
5 Setting the Clock
Mode
6 Selecting search
options for auto tuning
7
Selecting and
memorizing channels
8
Enjoy your TV.
If You Want to Rerun Plug & Play...
"
MENUP System Plug & Play
You should do Plug & Play again at home although you did in shop.
✎
NOTE
y To change the TV's setting from Store Demo to Home Use when not in Plug & Play, press the volume button on the TV.
When you see the volume bar on the screen, press and hold the
Plug & Play (Initial Setup)
Press the or button, then press the ENTER( button.
Select the desired OSD (On Screen Display) language.
Set up your network connection. Press the ENTER( button to start. If you do not know
your network set up information or want to set to it later, select Skip. We suggest you skip
network connection setup now and refer to "Network menu" in the e-Manual for set up
requirements and instructions, and the Network Connection section of this manual (Page 17).
You can set up the network connection later using the Network menu.
y Select Next to upgrade TV software. Your TV will automatically upgrade, if your TV
need a software upgrade. If you want to upgrade later, select the Skip. For more
information, refer to "Software Upgrade" (Preference Features
e-Manual.
✎
This may take some time, depending on network status.
Press the or button to select Home Use, and then press the ENTER( button
twice.
Select the Home Use mode. Store Demo mode is for retail environments.
Press the or button to select Auto or Manual, and then press ENTER( twice.
✎
If you selected Auto, you'll go to the Time Zone and DST screen. Select Time Zone
or DST, and then press ENTER(. On the Time Zone screen, use the
button to select your zone, and then press ENTER(. On the DST screen, press,
ENTER(, then select whether to turn DST (Daylight Savings Time) on or off. When
done, press ENTER(.
✎
If you selected Manual, you'll go to the Date and Time screen. Select Date or Time,
and then press ENTER(. Then, use the number buttons or the
set the date or time. Use the
done setting the Date and Time, select Next, and then press ENTER(.
Press the or button to select Air or Cable, and then press ENTER(. A check
appears on your selection. Select Next, and then press the ENTER( button. You can
check both if you have both connected.
✎
If you selected Cable, you'll go to the Cable System screen. Use the
to select Digital or Analog, and then press ENTER(. Use the
to select the correct cable signal format - STD, HRC, or IRC - and then press
ENTER(. Most cable systems use STD. Select the correct cable signal format for
both the Digital and Analog systems.
When done, select Next, and the press ENTER(.
The channel search will start automatically. This can take up to 30 minutes.
For more information, refer to Channel
✎
Press the ENTER( button at any time to interrupt the memorization process.
If you want to watch a broadcast program, select Close. If you want to enjoy Smart Hub,
select Smart Hub. Smart Hub will start. For more detailed information, refer to "Smart
Hub" in the e-Manual.
ENTER(
(QJOLVK  
or button to move between entry fields. When
Auto Program in the e-Manual.
MENU button on the TV for 5 sec.
Support Menu) in the
or
or button to
or button
or button