Toshiba M74 Series User Manual page 18

SETTING UP YOUR TV
There are 3 methods for Wireless Setup:
• Easy Setup - If the AP supports Wi-Fi Protected
Setup, this method can be used. Wi-Fi Protected
Setup is an industry standard designed to make
connection of wireless LAN equipment and
security setup easy. Wi-Fi Protected Setup will
automatically configure all wireless settings.
NOTE: WEP or TKIP encryption may not be
able to configured by easy setup.
• Assisted Setup - follow step 12.
Input the Security Key only.
• Manual Setup, skip to step 13.
Input the all settings.
NOTE: EXIT is available during settings.
k
In step 10, when you select Easy Setup;
Press BbC c to highlight Next and press OK.
The Easy Setup screen will appear.
Press c and B / b
Configuration) or PIN (Personal Identification
Number) and press OK.
Press b to highlight Start Scan and press OK.
PBC - Following the on-screen instructions, push
the appropriate button on your AP. When a window
reporting that the setup is complete appears, press
OK.
PIN - When the PIN code window appears, enter
the displayed PIN into your AP, and then press OK
to continue the PIN Setup. When a message
displays to report that the setup is complete, press
OK.
To cancel searching for the AP:
Press BACK while searching for the AP. A message will
C
appear, and then press
l
In step 10, when you select Assisted Setup;
BbC c
Press to highlight Next and press OK.
The Assisted Setup screen will appear.
Press B / b to select the desired AP and press
OK.
NOTE: Check the MAC address on the label of the
AP or in the manual, and select your AP.
B b
Press / to select Security Key and press OK.
The Software Keyboard window will appear (page
53).
Input the Security Key by using the Software
Keyboard. To save your setting, press the GREEN
button.
NOTE:
• The Security Key must adhere to these
conditions:
to select PBC (Push Button
c
/ to select Yes and press OK.
- AES, AES/TKIP: 8-63 ASCII or 64 Hex
characters
- WEP: 5 or 13 ASCII or 10 or 26 Hex characters
• There is only one key ID to set for WEP
encryption.
Press B / b
NOTE:
• If Network Name is not displayed, see Manual
Setup below to set Network Name before Done
is selected.
• If BACK is pressed before Done is selected,
settings are not saved.
When the message "Wireless configuration is
complete." appears on screen, press OK.
The screen will skip to step 14.
m
In step 10, when you select Manual Setup;
BbC c
Press
The Manual Setup screen will appear. Press
b to select Network Name and press OK.
The Software Keyboard window will appear (page
53).
Input the Network Name by using the Software
Keyboard. To save your setting, press the GREEN
button.
Press B / b
press c and
Shared Key, WPA2/WPA-PSK (mixed mode
WPA2/WPA) or WPA2-PSK. Press OK.
Press B / b to select Encryption, and then press
c and B / b
AES. Press OK.
NOTE:
• Certain encryption types are only compatible
with specific authentication types.
- When Authentication is Open System, only
WEP or None is compatible.
- When Authentication is Shared Key, only
WEP or None is compatible.
- When Authentication is WPA2/WPA-PSK
(mixed mode WPA2/WPA), only AES/TKIP is
compatible.
- When Authentication is WPA2-PSK, only AES
is compatible.
• When incompatible Authentication/Encryption
pairings are detected, a warning message will be
displayed, and no connection attempt will be
made until the incompatibility is resolved.
• There is only one key ID to set for WEP
encryption.
B b
Press / to select Security Key and press OK.
Input the Security Key by using the Software
Keyboard (page 53).
18
to highlight Done and press OK.
to highlight Next and press OK.
to select Authentication and then
B / b to select Open System,
to select None, WEP, AES/TKIP or
B /