Advertisement
Ô
Ô
NOTE
Connecting the Handset
Your local RadioShack store sells a variety of
longer coiled handset cords, which are
especially useful when you mount the phone
on a wall.
Using the Master/Secondary Setting
• If M is not set on at least one or more
phones, incoming calls might be
disconnected.
• If you connect only one system to a phone
line, set M/S to M.
• You can also connect other CID modules
that do not have the Call Waiting function to
the same phone line as your system, as long
as you do not connect more than four CID
modules total (including this phone).
• If you connect another type of CID module
that has Call Waiting (other than this system)
to the same phone line as your system, the
Call Waiting signal might be garbled or not
received.
Making a Call
If you dial a number over 15 digits, only the last
14 digits appear on the display.
Receiving a Call
• The NEW indicator remains flashing until
you have reviewed all new calls.
• The number of new calls does not change
until all calls have been reviewed and
NEW CALL
appears. The system new call
0
counter then resets to
.
Timer
If you lift the handset and don't dial a number,
the timer appears and starts to count up after
10 seconds.
2
2. Plug the other end of the cord into a
wall plate jack.
3. Align the base's keyhole slots with the
wall plate studs and slide the phone
downward to secure it.
4. To mount the phone directly on a wall
(after mounting the phone on a wall
plate), drill two holes 3
(83 mm) apart, one below the other.
5. Thread a screw into each hole, letting
the heads extend about 5mm from the
wall.
C
ONNECTING THE
Plug one end of the supplied coiled cord into
the handset's modular jack. Then connect it
to the jack on the left bottom of the base. Ô
S
U
P
ET
P THE
HONE
1. Hold down both
UP
ENTER LANGUAGE
four seconds until
ENG ESP FRA
appear, with
2. Press
or
UP
DOWN
language, then press
LCD CONTRAST
confirm.
appear on the display, with
3. Press
or
UP
DOWN
contrast level (1-5), and press
ENTER AREA CODE
to confirm.
_ _ _
then
appears, with the first
flashing.
4. Press
and
UP
DOWN
number of the area code, and press
END OF
to confirm the selection.
DELETE
5. Repeat step 4 to set the second and the
third digits.
S
R
ETTING THE
INGER
If you do not want to hear the phone ring,
slide
to
. You can still make
RINGER
OFF
calls with the ringer off, and you can still
answer calls if you hear another phone on
the same phone line ring. If you want to hear
the phone ring, set
RINGER
S
D
ETTING THE
IALING
Slide
to the setting for the type
TONE/PULSE
of service you have. If you are not sure
which type you have, do this simple test.
1. Slide
TONE/PULSE
handset and listen for a dial tone.
2. Press any number except
phone requires that you dial an access
code (
, for example) before you dial an
9
outside number, do not press the
access code number.
• If the dial tone stops, you have touch-
tone service. Set the switch to
• If the dial tone continues, you have
pulse service. Set the switch to
PULSE
U
SING
S
ERVICES
Some computer services require tone
signals for communications. If you have
1
/
inches
4
pulse service, you can still simulate special
tone service by following these steps.
1. Connect to the special service using
pulse dialing.
2. When the special service answers,
H
ANDSET
press * to temporarily switch to tone
dialing.
3. When you complete the call, hang up
and change the setting back to
U
SING THE
and
for about
DOWN
S
ECONDARY
, then
ENG
(Master/Secondary) lets you easily
flashing.
M/S
connect up to four system modules to the
to select the desired
same phone line, so CID and Call Waiting
to
DELETE
information can be set to more than one
1 2 3 4 5
and
phone on that line.
3
flashing.
1. Slide
to select the
2. Slide
DELETE
systems to
appears,
_
3. Set one system to answer; set the
others to off.
to select the first
OPERATION
M
AKING A
1. Pick up the handset and wait for a dial
tone.
2. Use the keypad to enter the number
you wish to dial. The number appears
on the display. Ô
3. When you complete your call, hang up
the handset. A few seconds later, the
to
or
.
HI
LO
number disappears, and the display
returns to normal.
M
ODE
R
ECEIVING A
When you receive a call, the phone rings
and the
NEW
the caller number appear on the display. To
to
. Lift the
TONE
answer the call, pick up the handset. Ô
T
. If your
IMER
0
This phone is designed with a clock timer to
count the off-hook time in seconds, up to
one hour. The timer appears on the display
and starts to count up when you dial a
number or answer an incoming call. Ô
.
TONE
U
SING
performs the electronic equivalent of
FLASH
a switchhook operation for special services,
.
S
T
PECIAL
ONE
.
PULSE
M
/
ASTER
S
ETTING
to
.
M/S
M
on all (up to three) other
M/S
. Ô
S
C
ALL
C
ALL
CALL#
indicator flashes.
and
F
LASH
Advertisement
