Axxera AX260 Installation & Owner's Manual

Axxera AX260 Installation & Owner's Manual

Power series mobile power amplifiers
Hide thumbs Also See for AX260:

Advertisement

AX260
AX440
AX460
AX490
AX3000M
AX4000M
AX5000M
POWER SERIES
INSTALLATION / OWNER'S MANUAL
Mobile Power Amplifiers

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the AX260 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Axxera AX260

  • Page 1 AX260 AX440 AX460 AX490 AX3000M AX4000M AX5000M POWER SERIES INSTALLATION / OWNER'S MANUAL Mobile Power Amplifiers...
  • Page 2: Before You Start

    INSTALLATION Preparation Please read entire manual before installation. Due to the technical nature of amplifiers, it is highly recommended that your Axxera amplifier is installed by a professional installer or an authorized dealer. Before You Start • i t a ( .
  • Page 3: Connection Descriptions

    INSTALLATION Connection Descriptions NOTE: Be sure to follow specific instructions included with your amplifier installation kit (not included with this amplifier). The information below should be used as a general guideline only. Power Wire (+12V) • D isconnect negative battery terminal before proceeding. Consult a qualified technician for instructions if you are unsure. • P lan wire routing before cutting any wires to length. Begin by routing the power +12V wire from the battery to the amplifier location. Use a grommet when running wires through the firewall or metal openings. Avoid running the power wire near...
  • Page 4 INSTALLATION Audio Inputs and Controls High Level Inputs Hi-Pass Filter RCA Line Inputs Crossover Mode Pass Through Low-Pass Filter Gain Bass Boost...
  • Page 5: Power And Speaker Connections

    INSTALLATION Power and Speaker Connections Remote Turn On Speaker Connections Ground Connection Fuse(s) +12VDC Battery Connection...
  • Page 6 INSTALLATION Audio Inputs and Controls RCA Line Inputs Bass Boost Pass Through Low Pass Filter Gain Slave/Master Controls Phase Control Data Link Subsonic Filter Remote...
  • Page 7 INSTALLATION Power and Speaker Connections Remote Turn On Speaker Connections Ground Connection Fuse(s) +12VDC Battery Connection...
  • Page 8: Typical Wire Routing

    Using an the same size power and ground wire. incorrect fuse could damage the amplifier. AX260 4 Ga. AX260 20A x 1 AX440 4 Ga. AX440 30A x 1 AX460 4 Ga. AX460 20A x 2 AX490 4 Ga.
  • Page 9: Amplifier Connections

    2 Speakers (stereo) Subwoofer (mono) Speaker Connections Connect speaker wires observing polarity. The minimum impedance load for the AX260, AX440, AX460 and AX490 is 2 ohms stereo and 4 ohms bridged. Use of loads lower than these is not recommended and may cause amplifier damage.
  • Page 10 INSTALLATION Connecting Two Amplifiers - Bridge Mode Master/Slave Mode The Dual mono amplifiers feature a Master/Slave mode, where two amplifiers can be connected together. When two mono amplifiers are connected together, the power from both amplifiers is combined.
  • Page 11 INSTALLATION Connecting Two Amplifiers - Bridge Mode Master/Slave Mode (cont.) *MASTER For master amplifier, set the switch to master. This will route the signal through Line-out to the slave amplifier. Set the phase to 0, all adjustments for gain and sound are done on this amplifier.
  • Page 12 INSTALLATION Configuration/Setup Input level Control The input level control (gain) is used to obtain the best possible match between the head unit audio output and the amplifier input. Begin by turning the input level control fully counterclockwise. Next, turn up the head unit volume control around 3/4 of the way up. Adjust the input level control clockwise until audible distortion is heard, then slightly counterclockwise to provide the best match. Repeat for all input level controls. Crossover Mode The crossover is used to filter out frequencies above or below a certain point. Choose LPF when using the amplifier with subwoofers, HPF when using with midrange/tweeter combinations and FLAT when using with coaxial-type speakers. Note: Choose FLAT when using the amplifier in stereo/bridged simultaneous mode. In this mode, passive crossovers are required. Failure to use the correct passive components may damage the amplifier and/or speakers. Consult a qualified professional for recommendations. Crossover This control allows precise adjustment of the Frequency Control crossover frequency.
  • Page 13: Troubleshooting

    INSTALLATION Troubleshooting Problem Cause Action +12V wire not connected or incorrect Check connections for proper Unit will not turn voltage. REM wire not connected or voltage (11~16VDC) incorrect voltage (no power LED GND wire not connected Check connection to ground indicator) Fuse(s) blown Replace fuse(s) Speaker wires not connected Check connections at speakers Volume turned all the way down Increase volume level at head unit One or more speaker wires touching Insulate all bare speaker wires from Unit has power - each other or touching chassis each other and chassis ground LED is green (but ground no sound)
  • Page 14: Specifications

    INSTALLATION Specifications Power output@14.4V <1% THD+N AX260 •56 Watts x 2 channels RMS @ 4 Ohms •90 Watts x 2 channels RMS @ 2 Ohms •190 Watts x 1 channel RMS @ 4 Ohms (bridged) Peak Music Power Output: 380 Watts Signal to noise ratio: 90dB (THD<...
  • Page 15 INSTALLATION Specifications Power output@14.4V <1% THD+N AX3000M •750 Watts x 1 channel RMS @ 2 Ohms •1000 Watts x 1 channel RMS @ 1 Ohm Peak Music Power Output: 3000 Watts Signal to noise ratio: > 80dB (THD < 0.5% @ 4Ω, 14.4V) Frequency response: 20Hz -150Hz (-3dB) Amplifier dimensions:...
  • Page 16: One Year Limited Warranty

    4. For more information and for the location of the nearest authorized service center Who is covered? This warranty is extended please contact us by one of the following to the original retail purchaser for products methods: purchased from an authorized Dual dealer and used in the U.S.A. • Call us toll-free at 1-866-382-5476 • E-mail us at cs@dualav.com What is covered? This warranty covers all defects in material and workmanship in Exclusion of Certain Damages: This warranty this product. The following are not covered: is exclusive and in lieu of any and all other software, installation/removal costs, warranties, expressed or implied, including...

Table of Contents